Search found 80 matches
- Tue Aug 28, 2007 11:15 pm
- Forum: Wanted
- Topic: Wanted Beretta' s
- Replies: 3
- Views: 2383
Wanted Beretta' s
Anyone Else???
- Tue Aug 14, 2007 12:46 am
- Forum: Suspension and Brakes
- Topic: Brake Bleeding Problems
- Replies: 11
- Views: 5367
Brake Bleeding Problems
most of the early abs systems needed a scanner to bled them corectly.. the motor cycles the valves and good bye old fluid..
Mr Goodwrench
Mr Goodwrench
- Tue Aug 14, 2007 12:20 am
- Forum: Wanted
- Topic: Wanted Beretta' s
- Replies: 3
- Views: 2383
Wanted Beretta' s
Wanted Beretta' s any year any model must be in Wisconsin area ...
will pay top $$$$
LMK
Thanks
Mr Goodwrench
will pay top $$$$
LMK
Thanks
Mr Goodwrench
- Tue Aug 14, 2007 12:09 am
- Forum: USA - Central
- Topic: Wisconsin
- Replies: 43
- Views: 33283
Wisconsin
Hay dont forget me!! If your in the wb area not far from me about 45 miles..
Mr Goodwrench
(by the way thats what I do)
Mr Goodwrench
(by the way thats what I do)
- Sat Jan 13, 2007 2:43 am
- Forum: Diagnostic Help
- Topic: Quad four problem
- Replies: 11
- Views: 3548
Quad four problem
YUP
Mr Goodwrench
were the coil towers black from carbon build up??
Mr Goodwrench
were the coil towers black from carbon build up??
- Wed Jan 10, 2007 12:39 am
- Forum: Diagnostic Help
- Topic: Having issues with A/C
- Replies: 4
- Views: 2155
Having issues with A/C
could it be a bad compres clutch? not locking up rightaway? or its grounding out?
Mr Goodwrench
Mr Goodwrench
- Wed Jan 10, 2007 12:30 am
- Forum: Diagnostic Help
- Topic: Help! somethings wrong!
- Replies: 2
- Views: 1676
Help! somethings wrong!
Also could be a cv axle gowing bad..
tie rod inner an outer.
Mr Goodwrench
tie rod inner an outer.
Mr Goodwrench
- Wed Jan 10, 2007 12:25 am
- Forum: Diagnostic Help
- Topic: Quad four problem
- Replies: 11
- Views: 3548
Quad four problem
QUOTErweatherford Fuel pressure regulator is on the end of the fuel rail.  Look for fuel coming out ...
- Sun Jan 07, 2007 12:02 am
- Forum: Diagnostic Help
- Topic: Misfire when engine is warm
- Replies: 8
- Views: 2921
Misfire when engine is warm
Also check your coil towers for junk on them. a brass wire brush works well. make shure to lube everything well..
Mr Goodwrench
Mr Goodwrench
- Sat Jan 06, 2007 11:54 pm
- Forum: Diagnostic Help
- Topic: Having issues with A/C
- Replies: 4
- Views: 2155
Having issues with A/C
Did you have any of the shops check to see if its charged with the proper amount of R-12/R-134.
If the system is low on fridgerent it wont be cold and the pump wont cycle properly..
Mr Goodwrench
If the system is low on fridgerent it wont be cold and the pump wont cycle properly..
Mr Goodwrench
- Sun Dec 31, 2006 1:27 am
- Forum: Diagnostic Help
- Topic: Antifreeze leak (need help)
- Replies: 9
- Views: 3022
Antifreeze leak (need help)
What a idea gm had a??? something abought warming the tb would warm the air gowing in to the engine making it run better better fuel combustion or some crap.
though air planes with carbs do have heaters in them so they dont freeze up..
Mr Goodwrench
though air planes with carbs do have heaters in them so they dont freeze up..
Mr Goodwrench
- Sun Dec 31, 2006 1:19 am
- Forum: Diagnostic Help
- Topic: throttle body gasket ?
- Replies: 6
- Views: 2726
throttle body gasket ?
U may have a pluged injector filter or a injector thats taking a crap. seen a few of 2.0 injectors just not spray right when they get older.. also check your tps sensor to make shur its reading correctly..
Mr Goodwrench
Mr Goodwrench
- Sun Dec 31, 2006 1:12 am
- Forum: Diagnostic Help
- Topic: ABS problem
- Replies: 6
- Views: 2531
ABS problem
the egr code is a funny thing. try to clean it an the tube an see if its better.. do you let your car coast at or above 35mph??? like comming to a stop sign? if you do it can set a code with pre obd2 cars 94 an older.. some thing with a low o2 count in pindle #3. u could try a new/updated one i...
- Sun Dec 31, 2006 12:53 am
- Forum: Diagnostic Help
- Topic: 2.8 wont idle and oil pressure low
- Replies: 21
- Views: 5289
2.8 wont idle and oil pressure low
some of the 2.8 an 4.3 had a special maf relearn or reflash of your ecm to new specs. But i havnt seen or done one in years
Mr Goodwrench
Mr Goodwrench
- Sun Dec 31, 2006 12:44 am
- Forum: Diagnostic Help
- Topic: Misfire when engine is warm
- Replies: 8
- Views: 2921
Misfire when engine is warm
I think its 12ohms per foot of wire like everyone said but plug wires can go faster than u think.  iv...