Search found 20 matches
- Fri Sep 22, 2006 4:50 pm
- Forum: Diagnostic Help
- Topic: My 3400 problems... going on for over a year...
- Replies: 8
- Views: 3142
My 3400 problems... going on for over a year...
I bet it would be a computer problem also. sounds like the only thing you havent tried.
- Thu Apr 20, 2006 11:25 pm
- Forum: Diagnostic Help
- Topic: Clutch work
- Replies: 1
- Views: 1304
Clutch work
where are the oil drips comming from? could be seals, a bleeder not seating right, a leaking quick disconnect...
- Wed Mar 08, 2006 10:24 pm
- Forum: Diagnostic Help
- Topic: Idles medium, Drives HOT
- Replies: 12
- Views: 3808
Idles medium, Drives HOT
It could be the headgasket too the system becomes unprimed and when you step on the gas it primes again.
A friend had this sort of problem before.
A friend had this sort of problem before.
- Wed Mar 08, 2006 10:18 pm
- Forum: Diagnostic Help
- Topic: Alternator belt install
- Replies: 24
- Views: 7330
Alternator belt install
Could this possibly be the alternator?
- Tue Feb 28, 2006 8:17 pm
- Forum: Members Rides
- Topic: The new beretta
- Replies: 4
- Views: 3149
The new beretta
They are made by Eagle Alloys. They came with the car when I bought it!!! No complaining here!
- Mon Feb 27, 2006 12:31 am
- Forum: Members Rides
- Topic: The new beretta
- Replies: 4
- Views: 3149
The new beretta
I got a few more pics after washing the dust and salt off
- Sun Feb 19, 2006 11:37 pm
- Forum: Members Rides
- Topic: 89 beretta GT
- Replies: 2
- Views: 1929
89 beretta GT
I can see why nobody cares about a smashed up beretta
- Thu Feb 16, 2006 8:48 pm
- Forum: Members Rides
- Topic: The new beretta
- Replies: 4
- Views: 3149
The new beretta
after wrecking the 89 GT back in dec 05 i got a 95 beretta
There are some pics of the car and on the second page there is my engine and tranny swap, you'll see why i needed to do the swap. I could hardly go reverse.
http://www.cardomain.com/ride/2261662
There are some pics of the car and on the second page there is my engine and tranny swap, you'll see why i needed to do the swap. I could hardly go reverse.
http://www.cardomain.com/ride/2261662
- Tue Feb 14, 2006 10:29 pm
- Forum: Members Rides
- Topic: 89 beretta GT
- Replies: 2
- Views: 1929
- Wed Jan 18, 2006 9:02 pm
- Forum: Appearance Mods
- Topic: Rusty engine block
- Replies: 2
- Views: 2024
Rusty engine block
I have a 2.2l that im putting into my 95 beretta.
The only problem is that it is soooo ugly, the block is all rusty. What is the best way to get rid of the rust without haveing to take the engine apart.
The only problem is that it is soooo ugly, the block is all rusty. What is the best way to get rid of the rust without haveing to take the engine apart.
- Sun Jan 15, 2006 6:44 pm
- Forum: FAQ
- Topic: Common problems with beretta's
- Replies: 69
- Views: 146880
Common problems with beretta's
I have a abs light on to I also have a 95. My problem is that the rear driverside wheel speed sensor is not working any more. You can tell if its the abs master cylinder or not if the light goes out after starting the engine and only goes on when you start moving. In this case like mine its probably...
- Fri Jan 06, 2006 4:57 pm
- Forum: Diagnostic Help
- Topic: Lights turn off?
- Replies: 2
- Views: 2110
Lights turn off?
Problem was the highbeam/lowbeam switch. The contacts were worn out
- Thu Jan 05, 2006 6:30 pm
- Forum: Diagnostic Help
- Topic: Coolant leaking at transmission
- Replies: 4
- Views: 2545
Coolant leaking at transmission
Just a suggestion here, but could it be a head gasket if was leaking enough drip down the side of the engine, down the tranny?
- Wed Jan 04, 2006 6:12 pm
- Forum: Diagnostic Help
- Topic: Won't Turn Over
- Replies: 18
- Views: 6668
Won't Turn Over
Ive had a battery that the voltage is fine when you measure it - no load. But when there is load - Starting it then the voltage goes down because of internal problems with the battery. Replace battery and it was good.
- Wed Jan 04, 2006 6:00 pm
- Forum: Diagnostic Help
- Topic: turn signal issues
- Replies: 7
- Views: 3225
turn signal issues
I just looked at the wiring diagram in my haynes manual and there is a hazard light flasher and signal light flasher so they are separate.