Search found 63 matches
- Fri Feb 15, 2008 10:41 pm
- Forum: Performance Mods
- Topic: more power, but secret
- Replies: 8
- Views: 3586
more power, but secret
3.4 stroker kit? Link?
- Fri Feb 15, 2008 10:24 pm
- Forum: Performance Mods
- Topic: Honing manifolds
- Replies: 14
- Views: 4646
Honing manifolds
60DegreeV6 has some ported 2.8 manifolds for $200. Just thought I would throw it out there. I was thinking about them for my 3.1.
- Tue Apr 04, 2006 11:42 am
- Forum: Diagnostic Help
- Topic: Oxygen Sensor
- Replies: 21
- Views: 7860
Oxygen Sensor
I supposed you already took a can of brake cleaner on a *COLD* engine while it was running and sprayed the brake cleaner over the vacuum lines, around the intake manifold, throttle body, etc. and listened for a change in idle while doing it... One place I had a problem was on the passenger side fron...
- Tue Apr 04, 2006 11:28 am
- Forum: Diagnostic Help
- Topic: abs
- Replies: 2
- Views: 2096
abs
You should just unplug the wire connectors (2 ones on top) on the master cylinder for the time being so that you can safely stop till you get the problem fixed.
- Tue Apr 04, 2006 11:25 am
- Forum: Diagnostic Help
- Topic: Idle problems
- Replies: 3
- Views: 2343
Idle problems
When I looked at the IAC and noticed the gunk I pulled off that thing on top and had a look inside its not clean but not obstructing anything. I reuse all my gaskets could this be the problem? They are getting pretty old... My EGR gasket especially... I also never replaced the O-ring on my IAC......
- Mon Apr 03, 2006 12:04 pm
- Forum: Diagnostic Help
- Topic: Idle problems
- Replies: 3
- Views: 2343
Idle problems
Ok I have a very unusual problem I can turn the car on when its cool and everything runs fine with the idle nice and steady, I drive it for 30 minutes... Then I turn the car off leave it for 20 minutes come back turn the car on and in park the idle will bounce from 1000-500. ÃÃ...
- Mon Apr 03, 2006 11:56 am
- Forum: Exhaust
- Topic: Catalytic Converter Placement?
- Replies: 6
- Views: 3518
Catalytic Converter Placement?
Hey thanks for all the posts I heard a Mach1 Mustang roar by the other day I am not sure with aftermarket exhaust or not but it sounded so hot. I am thinking now of just running 2.25" mandrel bend pipe over the rear axle then into a Flowmaster 40 series and myabe put a resonator if I need too....
- Thu Mar 23, 2006 12:49 pm
- Forum: Exhaust
- Topic: Catalytic Converter Placement?
- Replies: 6
- Views: 3518
Catalytic Converter Placement?
Ok everyone thinks that catalitic converters rob horsepower because back in the 70's they were big, inefficent, and restrictive but with todays technolgy its actaully possible to get great milage, horsepower and still save the environment. But thats not the point I want to bring up. All new cars ...
- Sat Mar 18, 2006 11:01 am
- Forum: Wheels and Tires
- Topic: Feretti Messina
- Replies: 11
- Views: 6009
Feretti Messina
Is that with rubber or not because if its that close without rubber your in some trouble.
- Tue Mar 14, 2006 7:09 pm
- Forum: Wheels and Tires
- Topic: Offset Question
- Replies: 3
- Views: 2837
Offset Question
I am also thinking of putting some wheel spacers on... guess i wont be able to lower my car much?
- Mon Mar 13, 2006 6:30 pm
- Forum: Wheels and Tires
- Topic: Offset Question
- Replies: 3
- Views: 2837
Offset Question
I think factory offset is like 32mm?
Will a 38mm offest wheel work? I am looking at a set of 17X7, with some low-pro rubber but most of the stuff i find is 38mm will it work? Rub issues?
Will a 38mm offest wheel work? I am looking at a set of 17X7, with some low-pro rubber but most of the stuff i find is 38mm will it work? Rub issues?
- Thu Dec 29, 2005 10:38 pm
- Forum: Suspension and Brakes
- Topic: Strut tower brace
- Replies: 19
- Views: 8179
Strut tower brace
I think its 90+ Cavaliers or Sunbirds if they ever had them.
- Fri Dec 09, 2005 11:15 am
- Forum: Diagnostic Help
- Topic: 3.1 oil pan gasket reusable?
- Replies: 3
- Views: 2350
3.1 oil pan gasket reusable?
Oh the money isnt an issue but it looks like a well designed gasket and the bolts arnt torqued very tightly so I figured that it was reusable and just needed some new silicone.
But if its not its no big deal. Thanks guys.
But if its not its no big deal. Thanks guys.
- Fri Dec 09, 2005 12:22 am
- Forum: Diagnostic Help
- Topic: 3.1 oil pan gasket reusable?
- Replies: 3
- Views: 2350
3.1 oil pan gasket reusable?
Well I pulled off the oil pan off my spare motor and it has like a 1/4" rubber gasket that looks reusable is it?
- Thu Dec 08, 2005 5:13 pm
- Forum: Intakes
- Topic: Intake questions
- Replies: 16
- Views: 9489
Intake questions
I hate the noise of my intake.  At idle it sounds like ***, when your actually moving it sounds reall...