Search found 4164 matches

by woody90gtz
Sat Jun 09, 2018 7:29 pm
Forum: General Questions
Topic: Dyno simulator
Replies: 8
Views: 185

Re: Dyno simulator

I've got one. It needs to know cam timing, compression ratio, cylinder head flow at each .100 lift and your basic exhaust.

When I put everything in for a stock 3400 it came up with 187hp, which is pretty close.
by woody90gtz
Wed Jun 06, 2018 2:39 pm
Forum: Announcements
Topic: Super Summit 2018
Replies: 2
Views: 216

Re: Super Summit 2018

Ohio, I figured. Looks sweet, but I'm pretty booked this year. Be a good one to hit next year though!
by woody90gtz
Mon Jun 04, 2018 10:53 pm
Forum: Members Rides
Topic: Not your average Z26... a resurrection
Replies: 181
Views: 20519

Re: Not your average Z26... a resurrection

Looks like a PTFE oil AN line? Those are such a prickly pain in the dick to assemble! haha
by woody90gtz
Sun Jun 03, 2018 11:25 pm
Forum: Members Rides
Topic: The Derretta, 1994 base with some attitude.
Replies: 498
Views: 59283

Re: The Derretta, 1994 base with some attitude.

What did you do for cables? IIRC I used the old barrel style rather than the eyelet.
by woody90gtz
Sun Jun 03, 2018 11:15 pm
Forum: Members Rides
Topic: Project 91 "SS" 3400/5spd
Replies: 1586
Views: 125195

Re: Project 91 "SS" 3400/5spd

Another couple weeks, another couple fights with this car. Still don't have my pushrods yet that I ordered about 3 weeks ago. I have a lifter tick because the way I measured originally is incorrect for pedestal rockers...it only works for stud rockers like I've used in the past. I talked to Ben and ...
by woody90gtz
Fri Jun 01, 2018 7:04 pm
Forum: Members Rides
Topic: The Derretta, 1994 base with some attitude.
Replies: 498
Views: 59283

Re: The Derretta, 1994 base with some attitude.

Some how I don't think you'll get much sympathy from Jon on that one. haha
by woody90gtz
Thu May 31, 2018 9:18 pm
Forum: Members Rides
Topic: Not your average Z26... a resurrection
Replies: 181
Views: 20519

Re: Not your average Z26... a resurrection

Your list just made me feel better... Haha
by woody90gtz
Fri May 25, 2018 2:39 pm
Forum: Diagnostic Help
Topic: Clunking around passenger side when making right turn
Replies: 7
Views: 165

Re: Clunking around passenger side when making right turn

Agreed. Those 96 style control arm bushings are known for problems. Sway bar end links could also be it, they could be bad or the arm could be bad where they mount.

High pitched squeak could be the wheel bearing.
by woody90gtz
Mon May 21, 2018 8:35 pm
Forum: General Questions
Topic: Drop-in LED bulbs for 91+ gauges?
Replies: 1
Views: 94

Re: Drop-in LED bulbs for 91+ gauges?

Two seconds on rockauto and then ebay, tada:
https://www.ebay.com/sch/i.html?_from=R ... odkw=pc194

PC194
by woody90gtz
Mon May 21, 2018 8:09 am
Forum: Members Rides
Topic: Not your average Z26... a resurrection
Replies: 181
Views: 20519

Re: Not your average Z26... a resurrection

I like that boxed axle, I bet it adds to the effective sway bar rate too.

How are you tuning for the woo wooer?

You should sell those wheels to Adam and get some Shoguns...haha :burn:
by woody90gtz
Mon May 21, 2018 12:40 am
Forum: Members Rides
Topic: Project 91 "SS" 3400/5spd
Replies: 1586
Views: 125195

Re: Project 91 "SS" 3400/5spd

Haven't updated in a while. Got it running decent with a base pulse constant of "100" and had to figure out some weird stuff with the idle oscillating. I've always burned chips and swapped them, but while I was researching TunerPro/Autoprom to troubleshoot my wibeband 0-5v datalog I learne...
by woody90gtz
Fri May 18, 2018 7:20 am
Forum: General Discussion
Topic: What Exhaust coat do you use?
Replies: 2
Views: 158

Re: What Exhaust coat do you use?

I had good luck using the VHT Flame Proof on my rear header last year. Blasted, paint only, then oven cure. This year though I did the front with their clear also. Blasted, painted, cleared and oven cured and it's already peeling off one of the tubes. Not quite sure why.
by woody90gtz
Wed May 16, 2018 8:01 am
Forum: General Questions
Topic: Options for Leather shift knob and shift boot??
Replies: 7
Views: 187

Re: Options for Leather shift knob and shift boot??

Mine is the leather Hurst knob from 4th gen Camaros. No pattern on it, just an H. But it's a comfortable, good looking knob that's cheap. 16mm thread. For the leather shift boot I had one sewed up by an upholstery guy. But I looked into adapting one from another car too. There is a BMW boot on eBay ...
by woody90gtz
Wed May 09, 2018 8:16 pm
Forum: General Questions
Topic: Taking a Beretta shell and building a chassis
Replies: 8
Views: 266

Re: Taking a Beretta shell and building a chassis

Alex is going "regular" T56 in his last I knew - no torque tube. I think he's trying to stay away from widebody too. Norm started the C5 corvette torque tube chassis Beretta, but gave up. The v8 RWD Beretta challenge is something I'd like to do some day. Roadster Shop and Schwartz are a co...
by woody90gtz
Wed Apr 25, 2018 9:50 am
Forum: General Discussion
Topic: Getrag shift cables
Replies: 32
Views: 1163

Re: Getrag shift cables

I know the shift arm is a square hole, I believe the select is too. I welded a nut on mine, but lathing a new pin/stud would make installation a lot faster and easier.

viewtopic.php?f=27&t=3868&start=1560

Go to advanced search