91-93 door panel issue.

Vent shades, black outs, things like that
User avatar
blindmandesigns
Registered User
Posts: 162
Joined: Sun Apr 23, 2006 4:26 pm
Location: Lancaster PA
Contact:

91-93 door panel issue.

Postby blindmandesigns » Mon Oct 09, 2006 8:58 am

I'm sure others have this issue, the door panel pops out from the black strip where the fabric meets the vinyl. This happens in my 91 and in the 92 but it's pretty bad in the 92. Is there any way to successfully fix this? the door panel is separating right where the curve is up top... COuld I seriously JB weld that back into place on the door panel... whatever needs to brace it needs to be STRONG. it sucks having to push that back into place each time I close the door it is the single thing that urks me about the quazar... aside.



User avatar
speedygtz
Registered User
Posts: 335
Joined: Wed Jun 28, 2006 11:09 pm
Location: lehighton
Contact:

91-93 door panel issue.

Postby speedygtz » Mon Oct 09, 2006 9:17 am

yea i had the same problem my dad stuk a screw in it and ran it down to far ....****** the door panel...

so if someone does have an answer id love to hear it cuz the door panels are maken the car look bad on the inside considering there the first thing ppl touch


the z26 is on the road!

User avatar
berettajunkie1991
Registered User
Posts: 217
Joined: Sat Jul 16, 2005 1:40 am
Location: Illinois
Contact:

91-93 door panel issue.

Postby berettajunkie1991 » Mon Oct 09, 2006 9:14 pm

i had the same problem what i did i took the panel off and put new fastners on it is because they are worn or maybe the support has come off gorilla glue works awesome on this problem when used correctly



User avatar
BerettaLove32
Registered User
Posts: 297
Joined: Wed May 29, 2002 5:40 pm
Location: Chicago
Contact:

91-93 door panel issue.

Postby BerettaLove32 » Tue Oct 10, 2006 4:49 pm

I have the same problem on my 93. i bought brand new fasteners and it still pops out. I do like the gorilla glue idea. Put some on new fasteners may be the answer.



User avatar
Chris88CL
Registered User
Posts: 290
Joined: Sat May 05, 2001 4:48 pm
Location: Calgary, Alberta
Contact:

91-93 door panel issue.

Postby Chris88CL » Tue Oct 10, 2006 10:43 pm

Try taking the door panel off and gluing on a strong piece of wood on the top edge (far enough in so it doesnt hit the black window trim when installed).  The reduced flex should stop it from popping out.  New fasteners are a must anytime you remove the door panel.  Also make sure the top screw is installed by the inner door handle.  Its the torx that goes in at an angle.  Make sure its tight.



User avatar
docrodg
Registered User
Posts: 137
Joined: Mon Aug 28, 2006 10:09 pm
Location: California and New York

91-93 door panel issue.

Postby docrodg » Thu Oct 12, 2006 7:26 am

Gorilla Glue or 5 minute epoxy is my fav. for a fix like this.  You can also peen it if you are careful but that looks horrid.  Glue the sucker.



User avatar
berettajunkie1991
Registered User
Posts: 217
Joined: Sat Jul 16, 2005 1:40 am
Location: Illinois
Contact:

91-93 door panel issue.

Postby berettajunkie1991 » Thu Oct 12, 2006 12:27 pm

your support bracket for the rear part of the panel has more than likely seperated all you need to do i apply gorilla glue to it and use new fastners just make the glue sets for like 24-36 hours so it is really nice and tight.



User avatar
stevetweis
Registered User
Posts: 4
Joined: Thu Aug 31, 2006 12:22 pm
Location: jersey

91-93 door panel issue.

Postby stevetweis » Fri Jan 05, 2007 2:12 am

i had this problem  long time ago. I remember all i had to do was get a new fastener and it popped back in place perfectly.  5 minute fix.




Return to “Appearance Mods”

Who is online

Users browsing this forum: No registered users and 3 guests