95 berretta ABS Brake Help

Want some new struts? What brand springs to buy? How much camber to run? What brake pads? What's the best setup for your situation....
BLADE
Registered User
Posts: 5
Joined: Mon Dec 06, 2010 7:36 pm

95 berretta ABS Brake Help

Postby BLADE » Fri Jul 06, 2012 9:50 pm

Guys I have had a Issue with my ABS Brakes since I pulled the Moter a couple years ago.

The ABS Light/Air Bag Light is On

Iv tried a few code readers but NO Success

Iv Done some Troubleshooting not much as I havent been able to find much info out there on GM ABS VI

But what I have found so Far is the The ABS Enable Relay Circut will not trigger the ABS Relay the Grey one by the Master cylinder with Key On Engine Running

What would stop EBCM from enabling the ABS relay??

1995 Chev Berretta 3.1 auto trans 4t60E


Any help would be awesome thanks in Advance



BLADE
Registered User
Posts: 5
Joined: Mon Dec 06, 2010 7:36 pm

Re: 95 berretta ABS Brake Help

Postby BLADE » Sat Jul 07, 2012 11:00 pm

I been doing some more testing found the EBCM and with a DVM been checking continuity

so Far the Wires for the ABS Electronic Brake Control Relay Control Circuit are Good no broken wires between the 2

What would stop the EBCM from Enabling the EBCM Relay Enable Circuit???? would a BAD wheel speed sensor stop it????
Whats the chain of events that happens in order

Or is it just a BAD EBCM????



BLADE
Registered User
Posts: 5
Joined: Mon Dec 06, 2010 7:36 pm

Re: 95 berretta ABS Brake Help

Postby BLADE » Sun Aug 26, 2012 6:06 pm

well guys I never did figure it out but I was able to get ahold of some wire diagrams and grounded the right wire and got the light off



Z26_T
Registered User
Posts: 364
Joined: Mon Oct 11, 2010 12:53 pm
Location: Indiana

Re: 95 berretta ABS Brake Help

Postby Z26_T » Sun Aug 26, 2012 9:43 pm

Yeah, when they don't have a ground they can be pretty upset


heavywoody wrote:Beretta, fast, reliable, and cost effective are words that should not be used in the same sentence.

95' BRM Z26. cammed/ported 3400/3500 Hybrid. HM282, OBD2, Garret T3/T04E 60 Trim, IC.

User avatar
3X00-Modified
Administrator
Posts: 10672
Joined: Thu Jul 05, 2007 9:18 am
Location: Plainfield CT
Has thanked: 12 times
Been thanked: 46 times

Re: 95 berretta ABS Brake Help

Postby 3X00-Modified » Mon Aug 27, 2012 7:50 am

To sum it up yes a bad wheel sensor will stop the ABS system from working.

You need to have it scanned by a shop that can read the ABS module. Then they can tell you what the fault is causing the light to come on. You can't do this with an autozone code reader either.



dsminit
Registered User
Posts: 4
Joined: Tue Feb 05, 2013 12:48 am

Re: 95 berretta ABS Brake Help

Postby dsminit » Tue Feb 05, 2013 1:26 am

I had a problem with mine pulled it out pulled bottom black cover and the middle gear had came lose!? Had a clicking noise when braking, tightened back up put some blue glue on it abs light went off no more clicking but no other lights where on...?




Return to “Suspension and Brakes”

Who is online

Users browsing this forum: No registered users and 6 guests