Page 34 of 36

Re: Beretta Z28

Posted: Fri Dec 30, 2016 7:36 am
by bonecrrusher
Make up a set of FB fenders - pull molds from them - and put in some CF mesh!

Re: Beretta Z28

Posted: Fri Dec 30, 2016 9:34 am
by jjanke
That's the idea...Scan existing surfaces, re digitize new wider surfaces, CNC female molds, lay up new fiberglass fenders.

Re: Beretta Z28

Posted: Sun Feb 19, 2017 9:05 pm
by jjanke
Door panels and rear firewall just about done :) feels good to be making some progress again!!!
16174966_10208127268481214_3763082643427657841_n.jpg
16406528_10208127268281209_4124232520497600875_n.jpg
16388121_10208127268921225_2599765397706762278_n.jpg

Re: Beretta Z28

Posted: Sun Feb 19, 2017 9:09 pm
by jjanke
i have also been working on cleaning up and organizing the interior wiring harness

Re: Beretta Z28

Posted: Mon Feb 20, 2017 10:12 am
by bonecrrusher
Updates.... yessss!

Re: Beretta Z28

Posted: Mon Feb 20, 2017 10:29 am
by jjanke
Haha I've been working on on it a bunch more lately but the wiring harness work is taking forever ancin a picture doesn't look like progress in pics :/

Plus some other projects were stealing time an attention as well

Re: Beretta Z28

Posted: Tue Feb 21, 2017 12:33 pm
by themixer
when is it burnout time?

Re: Beretta Z28

Posted: Tue Feb 21, 2017 1:13 pm
by jjanke
Hope to be wasting tires by mid to end of summer. But most likely next summer. :)

Re: Beretta Z28

Posted: Thu Feb 23, 2017 8:01 am
by woody90gtz
jjanke wrote:Hope to be wasting tires by mid to end of summer. But most likely next summer. :)

I hear ya there. Haha

What about stretching the stock steel fenders? I've seen people weld in a pie-cut to stretch them without doing the huge flare look.

Re: Beretta Z28

Posted: Thu Feb 23, 2017 6:04 pm
by jjanke
maybe it would work if i just needed an inch ..... the wheels are way out there...... plus im planning on test fitting some extended upper and lower control arms to gain even more steering angle. which is gonna push the wheels out another 2 inches if i go that route..... im gonna need a widebody for my widebody :)

Re: Beretta Z28

Posted: Fri Feb 24, 2017 9:01 am
by themixer
Step 1: ?????
Step 2: Install drivers seat
Step 3: Burnouts

Re: Beretta Z28

Posted: Fri Feb 24, 2017 9:26 am
by jjanke
Hahaha I love themixer's enthusiasm!!!!! There will be burnouts!!!!!!!

Re: Beretta Z28

Posted: Fri Feb 24, 2017 12:16 pm
by themixer
i have some of the list done for you just finish up step one, no big deal right?

Re: Beretta Z28

Posted: Sat Feb 25, 2017 7:57 pm
by jjanke
This will be the first step in creating the wide body kit for the Beretta. (If my plan works) We finished scanning and digitized the existing surfaces of
16832213_10208341960928391_8101207258042867497_n.jpg
the Beretta. Now it's time to get WIDE !!!!!
16995954_10208341961208398_8481171415847356505_n.jpg
16999094_10208341960648384_7221855404494005693_n.jpg

Re: Beretta Z28

Posted: Tue Feb 28, 2017 9:57 am
by themixer
that is very ideal, have to have something to keep the rubber off the rear quarter from doing large burnouts.