Page 1 of 1

Iat resistor mod

Posted: Fri Aug 02, 2002 5:17 pm
by stizkidz
today, i completed the infamous iat resistor mod.  what i did was connect 4.7k and 3.3k resistors in a series together to make 8.0k.  i then cut the wires from the iat and spliced the two wires to either end of the 8.0k resistors.

my question is:  did i waste $2 doing this mod?  i was unsure if this mod made any difference whatsoever but i had some free time so i decided to do test it out...  so far, i have noticed no changes in idle or normal driving whatsoever...  

i figured that since i have the cone filter intake that it sucks up so much hot air that having the intake temperature reading be constant that it would improve the timing under hot driving conditions.

any input?
thanks,
-Ben

Iat resistor mod

Posted: Sat Aug 03, 2002 7:49 pm
by Guest
The resistor mod is just a myth. By tricking the computer into thinking you have cooler air, you are making your a/f ratio more rich, and therefore, wasting gas. If you want cool air make a cool air intake, dont go cheap. ;)

Iat resistor mod

Posted: Sat Aug 03, 2002 10:09 pm
by stang&2Birds
Quote (beretta3100 @ Aug. 03 2002,7:49)
By tricking the computer into thinking you have cooler air, you are making your a/f ratio more rich, and therefore, wasting gas.

Nope, not even close.  When the car is warm, THE O2 SENSORS RULE THE WORLD!!!.  Jeeze, WHAT do people think O2 sensors do and why they are there?

 The *in-line* resistor mod will do 2 main things:
o Your car MAY run richer at WOT.  So, it MAY help with qtr miles time.  It will NOT help at all during regular driving.

o During cold start, your car will run even RICHER (not really a good thing).  That will SHORTEN the life of the cats by "some amount".


 So, if you do an IN-LINE resistor mod, it will "probably" not do anything good or bad.  If you replace your intake temp sensor with a resistor, then that is just plain foolish.  Shows a complete lack of understanding of FI.

IMHO:  Money is better spent on A BOOK.  What a concept, huh? ;)  See amazon.com, the one by Probst is a good first start.

Iat resistor mod

Posted: Sun Aug 04, 2002 12:29 am
by Guest
As I said before... The Resistor mod wont help at WOT(because of the comp getting a reading from the 02). The only thing it might help is "maybe" when your stopped using a CONE air filter under the hood. It might help you get a bit more fuel when you try to go from a stop...
I don't know where you came up with like all those resistors connected together tho..
2 15 K in parallel.. or 8.2 only is abt the value you need.
I'm too lazy to figure out what resistance your using..

Iat resistor mod

Posted: Sun Aug 04, 2002 1:37 am
by stizkidz
ok ok!

i get the point...  so im an idiot, lol.
anyway...

someone with a good understanding of FI, please give me some good advice on how i should run my iat setup the most effective way possible.  i currently have the standard stock intake tubing with the 11" big K&N cone filter on the end of it.  i can easilly tap a hole into the hose for the iat or i could easilly move it anywhere else on the car.  based on the current setup, the cone sucks up a ton of hot air and after 15 minutes of driving i can feel the engine bogging down when i step on it.

anyone that can give me some helpful advice, i would greatly appreciate it.  (as you can see, im desperatate and trying thisngs that dont work.)

thanks,
-Ben

Iat resistor mod

Posted: Sun Aug 04, 2002 2:35 pm
by RebelGT
Quote (stizkidz @ Aug. 03 2002,11:37)
someone with a good understanding of FI, please give me some good advice on how i should run my iat setup the most effective way possible.  anyone that can give me some helpful advice, i would greatly appreciate it.  (as you can see, im desperatate and trying thisngs that dont work.)

use the STOCK IAT setup, and get a chip from ben (www.60degreev6.com) , stop trying to fool the computer, just change it.

Iat resistor mod

Posted: Tue Aug 06, 2002 12:47 am
by stizkidz
ok,

i reconnected the wires tonight (from the iat to the iat wires).  do you get an SES light if you do it wrong cause i may have reconnected the wires the wrong way...  if this is possible let me know.  if not, then im switching back to the resistor cause now it is surging badly at idle with the normal iat reconnected.

-Ben

Iat resistor mod

Posted: Tue Aug 06, 2002 5:50 pm
by Guest
Quote (stizkidz @ Aug. 06 2002,12:47)
ok,

i reconnected the wires tonight (from the iat to the iat wires).  do you get an SES light if you do it wrong cause i may have reconnected the wires the wrong way...  if this is possible let me know.  if not, then im switching back to the resistor cause now it is surging badly at idle with the normal iat reconnected.

-Ben

No you can't connect it backwards. Its just a resistor that varies with temp (thermistor).. I don't know why you cut it tho. Make sure you connected the wires back together good...like solder them together is how you should do it.