Spectre Industries 8208 Air Intake Kit

Post information about intake systems. Either purchased or custom made
User avatar
Mikes_95_Berry
Registered User
Posts: 33
Joined: Mon Oct 17, 2005 5:50 am
Location: Binghamton NY

Spectre Industries 8208 Air Intake Kit

Postby Mikes_95_Berry » Sun Apr 27, 2008 10:05 pm



Installed it Friday and been test driving. Better is many ways. I was shocked by the fuel milage im getting now. I swear at least 5 more MPG. Bizzare! I need to do more driving to see... but still got a lot of work to do on my 'retta

Should work with any filter that has a 3 inch diameter hole.

My setup needed to a second coupler. Comes with a black one. Bought a blue coupler at the local Autozone. I've looked at a few Air Intake setups for 2.2 but this one is the best Ive seen... and done! Going to try to make it CAI a little later.

Summit Racing has the Spectre Industries 8208 kit .







My Raspberry Metallic 95 Beretta 2.2 5 Speed @ CarDomain

My 1998 Dodge 1500 Magnum V6 "Shorty" @ CarDomain

User avatar
Money pit Beretta
Registered User
Posts: 6362
Joined: Thu Jul 26, 2007 11:36 am
Location: Kansas
Has thanked: 2 times
Been thanked: 9 times

Spectre Industries 8208 Air Intake Kit

Postby Money pit Beretta » Tue Apr 29, 2008 7:17 pm

You still have the old box in? fastlane02 is building a shop, try to get in touch with him on the CAI. Didn't you have a IAT, what happened to it? Just asking, not putting you down. I had a home made intake for my 90Gt that I made with plastic drain pipe and rubber pipe couplers(used with the stock box). It was fun to make. Later I got a CAI from Tranzgenic.


keep'em flying!

payback
Registered User
Posts: 71
Joined: Thu Mar 18, 2004 12:22 am
Location: Central NY
Contact:

Spectre Industries 8208 Air Intake Kit

Postby payback » Wed Apr 30, 2008 1:13 pm

looks nice, wow u live right next to me!finally an active member near me.


'96Z26:Eibach springs, KYB struts, GM Strut brace, K&N cone

User avatar
Mikes_95_Berry
Registered User
Posts: 33
Joined: Mon Oct 17, 2005 5:50 am
Location: Binghamton NY

Spectre Industries 8208 Air Intake Kit

Postby Mikes_95_Berry » Wed Apr 30, 2008 8:21 pm


(Money pit Beretta @ Apr. 29 2008,18:17)
QUOTE
You still have the old box in? fastlane02 is building a shop, try to get in touch with him on the CAI. Didn't you have a IAT, what happened to it? Just asking, not putting you down. I had a home made intake for my 90Gt that I made with plastic drain pipe and rubber pipe couplers(used with the stock box). It was fun to make. Later I got a CAI from Tranzgenic.

I put the IAT next to the brake booster pointed to the firewall which is held in place with a velco strap. Did this as explained in a post on one of the two Beretta forums or Cavalier ones. Cant remember which it was. As long as you get cold air to it, it works fine.

The airbox is no longer on the car. The pic was taking before I pulled it out.

Building the CAI using some stuff I found on ebay. The ones for the Grand AM with V6 will work. There are two of them that sell the kit, N-Take and the other is Best Car Part. Either one of those should do the trick. just need to had a 22 degree bend and some straight piece to finnish. Ill show the pics of it when I get the parts and have it installed.



My Raspberry Metallic 95 Beretta 2.2 5 Speed @ CarDomain

My 1998 Dodge 1500 Magnum V6 "Shorty" @ CarDomain

User avatar
Mikes_95_Berry
Registered User
Posts: 33
Joined: Mon Oct 17, 2005 5:50 am
Location: Binghamton NY

Spectre Industries 8208 Air Intake Kit

Postby Mikes_95_Berry » Wed Apr 30, 2008 8:26 pm


(payback @ Apr. 30 2008,12:13)
QUOTE
looks nice, wow u live right next to me!finally an active member near me.

Been active since 2005. :) But mostly was posting on Bstuff. Till is started having it's problems.

There are a few other 'retta NY'ers between the 2 forums.



My Raspberry Metallic 95 Beretta 2.2 5 Speed @ CarDomain

My 1998 Dodge 1500 Magnum V6 "Shorty" @ CarDomain

User avatar
Money pit Beretta
Registered User
Posts: 6362
Joined: Thu Jul 26, 2007 11:36 am
Location: Kansas
Has thanked: 2 times
Been thanked: 9 times

Spectre Industries 8208 Air Intake Kit

Postby Money pit Beretta » Wed Apr 30, 2008 10:33 pm

Just checking on the IAT, a few times I have read posts where someone takes it off, as I'm sure you have. Back when I made the old intake I found a stang site that had all the bends and straight pipe you could want(wish I would have saved it, I did a CAI search, I know it doesn't help, but it is out there). You know, I think that I found it by looking for Vibrant silicone couplers(connecters). If you have the time look around and if you find it tell me.


keep'em flying!

JeffD
Registered User
Posts: 467
Joined: Tue Feb 07, 2006 9:44 pm
Location: new york

Spectre Industries 8208 Air Intake Kit

Postby JeffD » Wed May 07, 2008 5:37 pm

Man, just put that IAT sensor in the tube where it belongs, other than that looking good! a CAI would be even better though! I've been thinking about moving my battery to the trunk and making a sealed aluminum CAI box in the front corner, something you should think about too.
Hey, I make my way down to Binghamton sometimes, you ever go to Gary's U-pull it?
I got all my Z34 stuff from there!


1988 Beretta GT 5 speed - 1st car... Gone to the crusher. :(
1989 Beretta GT Z-51
1994 Beretta Z26 getting FE7+Z51 goodies
1987 Pontiac Bonneville LG3+4T65-E
1987 Chevrolet Celebrity Wagon L36+4T65-E
1998 Chevrolet C1500 5.7L L31+ built 4L60-E

User avatar
Mikes_95_Berry
Registered User
Posts: 33
Joined: Mon Oct 17, 2005 5:50 am
Location: Binghamton NY

Spectre Industries 8208 Air Intake Kit

Postby Mikes_95_Berry » Sun Jun 22, 2008 10:04 pm

Whoa... I is a little late with reply...

this is where the IAT sits... right where I said it was. ( Strut Bar has been removed for better view )


I driven over 1,000 miles with it like this. Has ZERO issues with performance or fuel milage. Check engine light has never come on... BUT it may have an issue with Emission Inspection. Which doesnt matter to me... I still have the stock stuff to put back on.

scberetta3800
QUOTE
Hey, I make my way down to Binghamton sometimes, you ever go to Gary's U-pull it?
I got all my Z34 stuff from there!


I live 8 minutes away from there. Where you think I got my Z04 stuff from :D

Updated with a new Spectre cone and coupler...








My Raspberry Metallic 95 Beretta 2.2 5 Speed @ CarDomain

My 1998 Dodge 1500 Magnum V6 "Shorty" @ CarDomain

User avatar
fastlane02
Registered User
Posts: 315
Joined: Tue Nov 06, 2007 10:00 pm
Location: Warren, IN

Spectre Industries 8208 Air Intake Kit

Postby fastlane02 » Mon Jun 30, 2008 6:00 pm

if you run a 90 bend stait over behind your battery and then down beside it. you can make a cai. good luck


CBC PERFORMANCE

use to be grace89SS
89gt 3.8scII to much to list.
87 iroc-z the old girl is getting a make over!
90 gtz bring her back to her glory days but even better!
02 TA moser 12 bolt,yank 4k stall, spohn everything, LPE heads,MS4 cam,fast90/90 ported, hooker lt sc.
68 firebird

payback
Registered User
Posts: 71
Joined: Thu Mar 18, 2004 12:22 am
Location: Central NY
Contact:

Spectre Industries 8208 Air Intake Kit

Postby payback » Thu Jul 17, 2008 2:21 am


(Mikes_95_Berry @ Apr. 30 2008,19:26)
QUOTE

(payback @ Apr. 30 2008,12:13)
QUOTE
looks nice, wow u live right next to me!finally an active member near me.

Been active since 2005. :) But mostly was posting on Bstuff. Till is started having it's problems.

There are a few other 'retta NY'ers between the 2 forums.

hey guys im one of the central ny'ers! utica ny here.


'96Z26:Eibach springs, KYB struts, GM Strut brace, K&N cone

User avatar
Styluss
Global Moderator
Posts: 1916
Joined: Tue Jan 24, 2006 6:48 pm
Location: Lakewood, Colorado
Has thanked: 9 times
Been thanked: 6 times
Contact:

Spectre Industries 8208 Air Intake Kit

Postby Styluss » Sat Oct 18, 2008 11:56 am

I can help you make that a cold air setup.
I have the piping, couplers clamps and more in stock right now.

This is what it would end up looking like...



BFest 2013: Denver Colorado Host & Committee Member
Winner: Best Custom Late Model Interior
Gopher Award - Tin Foil Award - Banner!


Return to “Intakes”

Who is online

Users browsing this forum: No registered users and 2 guests