Car wont run getting code 33
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
I'm positive they are not wrong I'm wondering if I might of missed a lifter when putting the rod in and the exhaust valve stayed closed this would kind of explain why my starter is bogging down regardless I'm ripping it back down tonight
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
Re: Car wont run getting code 33
I'll wait and see. Don't read into that too much. Just would like to hear everything is right and it's something easy to fix.
keep'em flying!
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
So I removed the intake manifold and all pushrods seem to be in right place
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
Scratch that they are in the right places I see no damage to anything all the springs are intact even the inner spring no bent pushrods either
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
If I want to manually crank the motor to see everything in motion which way should I turn it
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
Will or should the crank turn with no pushrods in I would assume no cuz all valves are closed
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
I'm just trying to figure out why my starter is bogging down when it cranks the motor over maybe my ecm bit the dust
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
http://s300.photobucket.com/user/Corvet ... 4.mp4.html
this is what it sounds like
this is what it sounds like
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
My brother thinks the timing is out like it slipped a tooth but It ran here fine
Re: Car wont run getting code 33
Put the map sensor's vacuum line to a dedicated port not shared to any other line and make sure the pcv hose is not broken and is secured in place.
Compression check the engine.
did you put rtv on the flat surfaces where lim meets block?
Check your ground circuit to the map.
Compression check the engine.
did you put rtv on the flat surfaces where lim meets block?
Check your ground circuit to the map.
_________
-------------
-------------
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada
Re: Car wont run getting code 33
Rtv was done
Vacuum line to map was checked and holds pressure
I don't have a comp tester I have to try and grab one from someone
Ill check the map ground
Thanks for every ones help
Vacuum line to map was checked and holds pressure
I don't have a comp tester I have to try and grab one from someone
Ill check the map ground
Thanks for every ones help
-
- Administrator
- Posts: 1775
- Joined: Wed Mar 03, 2004 10:03 pm
- Location: Long Grove, IL
- Contact:
Re: Car wont run getting code 33
I would verify that the plug wires are installed correctly and maybe even do a compression test.
Cliff Scott
- 3X00-Modified
- Administrator
- Posts: 10912
- Joined: Thu Jul 05, 2007 9:18 am
- Location: Brooklyn CT
Re: Car wont run getting code 33
I'm going to say it is near impossible to slip a tooth on the V6 chain timing setups... Hell I drove to CO and back with a stretched to F timing chain and it never had the opportunity to slip, and it was STRETCHED OUT. So I highly doubt that's the issue.
-
- Registered User
- Posts: 423
- Joined: Thu Mar 06, 2014 10:28 am
- Location: New West B.C. Canada