Upgrade To 12" Front Brakes

Want some new struts? What brand springs to buy? How much camber to run? What brake pads? What's the best setup for your situation....
User avatar
heavywoody
Global Moderator
Posts: 1849
Joined: Sun Nov 03, 2002 4:10 pm
Location: Concord, NC
Has thanked: 8 times
Been thanked: 15 times
Contact:

Upgrade To 12" Front Brakes

Postby heavywoody » Mon Mar 10, 2008 10:32 am

Use this information at your own risk... I take no responsibility for any failures when doing this modification to your vehicle. You are fitting a part to the car that was not intended for it so the chance of some issue is always present.

***This post is a work in progress... I will update it as I complete the project.***

Larger rotors will absorb and radiate more heat allowing more use of the brakes when needed.

Dual piston calipers offer more bite, and provide braking pressure along a larger surface area (due to larger pads), which aids in faster stopping.

One thing to keep in mind is that larger rotors weigh more. Thus, your rotational mass will increase. However, keep in mind that you will be switching from a cast iron knuckle to a cast aluminum piece. You'll also be switching from a cast iron caliper to a cast aluminum caliper. While your rotational mass will increase, your unsprung weight will decrease. I'll collect weights as I go along.

Weight Comparisons

Knuckles
Stock - 9.7 lbs
N-body - 4.1 lbs

Hubs
Stock - 5.4 lbs
N-body - 7.2 lbs

Rotors
Stock - 11.6 lbs
F-body - 18.7 lbs

Outer CV
Stock -
N-body - 5 lbs

Calipers (with pads)
Stock - 9.7
C5 (including F-body abutment bracket) -

***DISCLAIMER***

This upgrade will require you to have dual bolt pattern wheels, as doing this upgrade will change your wheel pattern in the front to 5x115.

You will more than likely need 17" wheels, as this setup doesn't fit under MOST 16" wheels... it might on some, but check clearances before you install. I know that the brake setup will clear the 97-03 Grand Prix Hi-polish Torque Star wheels (I have these brakes on my GTP).

Parts Needed:
99-04 N-body Aluminum Spindles and strut knuckle bolts (Grand Am, Alero, Malibu)
99-04 N-body Front hubs
99-04 N-body Front lower ball joints
99-04 N-body Outer CV joint
98-02 F-body Front Rotors (users choice in brand/style)
98-02 F-body Calipers (must have the abutment bracket)
98-02 F-body Brake pads (users choice in brand)

Other parts that work:
63010220ERL x2 3an to 10mm(3/8) Banjo 20" Hose << Aftermarket SS line that works with the F-body and N-body upgrade depending on which your doing
989534ERL x2 Brake Adapter 3an to 10mm x 1.0 Female NOT Inverted Flare. << Adapt factory Lines to 3an Stainless steel lines. Double check your factory lines, if they've been replaced they may be a different thread and possibly inverted flare type.

C5 Corvette Calipers (have a different casting, reduces flex in the calipers)
*Note* If using C5 calipers, purchase brake pads for an F-body car, as the pads used are based on which abutment bracket will work, not the caliper. C5 abutment brackets will not bolt up to these knuckles.

Benefits to using a C5 caliper are that the caliper is pressure cast, instead of gravity cast. This helps increase the life and strength of the caliper. As mentioned above, the caliper also has a different, more rigid casting. On the C5 caliper, the ribs cover the entire top of the caliper, where as the F-body calipers, only half of the caliper is ribbed.

F-body caliper:
Image

C5 caliper:
Image

More information (thanks to Brendan)

theres just a couple of parts you said that can be changed.  this is from a post where many people have done it this way. ive seen the post on some grand prix site about the f-body swap.
QUOTE1) Order these parts:
- 98-02 fbody caliper brackets (front) (P/N: 18026163) $61/each
- 97-04 Corvette calipers
---grey calipers: (P/N: 12530682)(P/N: 12530683)$100/each
---red (zo6) calipers: (P/N: 88895128)(P/N: 88895129) $96/each
- 98-02 fbody brake pads (front)
- 00-05 Impala rotors (front)
- 97-02 corvette anti-rattle clip
* all part numbers are GM numbers.
** the calipers are available at auto part stores for less, but are not GM original parts.
More Information: http://www.grandamgt.com/forum/showthread.php?t=62144

Installation:

You will need to remove your CV axles, knuckle assembly, calipers, rotors, and ball joints.

Install the new ball joints into your control arm.

The N-body spindles look like this:
Image

Notice how there is an extra portion on the knuckle... N-bodys use the spindle/knuckle for steering, where as L-bodys use the struts. The extra part will have to be removed, as seen below.
Image

Image

Image

Since we are using N-body knuckles, we are going to have to use N-body hubs. This is why you'll need dual bolt pattern wheels, as the N-bodys have 5x115 bolt patterns. You could have an adapter sleeve made to fit into the N-body knuckle, and use an L-body hub to retain your wheels, but this won't work on ABS cars since there isn't a spot to mount the ABS sensor on the N-body knuckles. To get that to work, you'd have to find a spot to mount the sensor, and mimic the mounting style used on the L-body knuckles so your ABS will still work. If you go this route, you won't have to mess with the axles.

Here is the bracket that the ABS sensor mounts to on the N-body. This goes between the hub and the knuckle.
Image

Now we need to switch the Outer CV from the N-body axles onto the L-body axles. To remove the Outer CV, you have to remove the metal banding on the boot, pull the boot down, and spread the C-clip that keeps the Outer CV on the axle. Follow this procedure for both axles, and just swap them, making sure that you keep the race cage facing the same way upon reinstallation (so that you will have access to the C-clip if you have to swap axles down the road).

C-clip
Image

Axle w/ removed Outer CV
Image

When you put the axles back together, make sure to use wheel bearing grease for CV's, and not the tube grease that you put into ball joints and tie rods.

Install the axles back into your car.

Install the hub into the knuckles.

Install the spindle assembly (knuckle and hub bearing) into the car, putting the axle through the hub. Make sure to use the strut knuckle bolts from the N-body, as the holes in the knuckle are smaller than the L-body holes.
Image

Image

Image

Put the F-body rotor on.
Image

Install the abutment bracket.
Image

Install the pads, then the calipers of your choice, making sure to have the bleeder screws pointing up.
Image

Bleed the brakes, and enjoy your new-found stopping power! MAKE SURE TO CHECK CLEARANCES OF YOUR BRAKE LINE BEFORE GOING ON A TEST DRIVE! YOU DO NOT WANT THE LINES TO RUB ON YOUR TIRES OR ANY OTHER SUSPENSION/STEERING COMPONENT!

More information that may help you with the swap: http://www.j-body.org/forums/read.php?f ... 30&t=99830

Here are some more semi-finished pics (I still need to get brake lines and my pads aren't installed in these pics).
Image

Image


Geoff
95 Z26 3400 5spd
Beretta Preservation Society - Director of Acquisitions
Image

User avatar
heavywoody
Global Moderator
Posts: 1849
Joined: Sun Nov 03, 2002 4:10 pm
Location: Concord, NC
Has thanked: 8 times
Been thanked: 15 times
Contact:

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby heavywoody » Mon Mar 10, 2008 10:33 am



This next one shows the difference in size of the stock rotors compared to the F-body rotors... 10.125" vs 12.19"



Geoff
95 Z26 3400 5spd
Beretta Preservation Society - Director of Acquisitions
Image

User avatar
quad4berettagtz
Administrator
Posts: 924
Joined: Thu Aug 28, 2003 10:06 pm
Location: Green Bay, WI
Been thanked: 2 times
Contact:

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby quad4berettagtz » Mon Mar 10, 2008 10:37 am

God that is sweet....  I wonder if I would benefit from that in autox, or just flat spot my tires   :;):


Mike - Beretta.net Committee Chairman
'90 Med Garnet GTZ<-250K original Quad 4 miles!
'90 Black GTZ SCCA Solo II #24 DSP<-still sleeping!
'95 Raspberry Z26<-DD duties until GTZ fuel pump is fixed!

User avatar
Chazzman
Registered User
Posts: 280
Joined: Thu Jun 28, 2001 8:55 pm
Location: Hillsdale Michigan
Contact:

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby Chazzman » Mon Mar 10, 2008 3:40 pm

WOW,  Time to start scavenging at work for some stuff..... already got the F-body stuff at home .


'92 GT-Z 3.1L 5spd lot's of GO FAST stuff  :banana

User avatar
fastlane02
Registered User
Posts: 315
Joined: Tue Nov 06, 2007 10:00 pm
Location: Warren, IN

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby fastlane02 » Mon Mar 10, 2008 7:50 pm

now you need to start on a big brake setup on the back


CBC PERFORMANCE

use to be grace89SS
89gt 3.8scII to much to list.
87 iroc-z the old girl is getting a make over!
90 gtz bring her back to her glory days but even better!
02 TA moser 12 bolt,yank 4k stall, spohn everything, LPE heads,MS4 cam,fast90/90 ported, hooker lt sc.
68 firebird

User avatar
heavywoody
Global Moderator
Posts: 1849
Joined: Sun Nov 03, 2002 4:10 pm
Location: Concord, NC
Has thanked: 8 times
Been thanked: 15 times
Contact:

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby heavywoody » Mon Mar 10, 2008 8:26 pm

Yeah, I know... I have other things to finish up first though. That will probably wait til next winter.

The F-bodies have more clearance since the ribbing doesn't extend across the top of the caliper... so those thinking about doing this with aftermarket 16" wheels should probably look at those calipers.


Geoff
95 Z26 3400 5spd
Beretta Preservation Society - Director of Acquisitions
Image

User avatar
fastlane02
Registered User
Posts: 315
Joined: Tue Nov 06, 2007 10:00 pm
Location: Warren, IN

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby fastlane02 » Mon Mar 10, 2008 10:11 pm

i need my c&c guy to get back so he can make the spindles so you can use stock beretta rims. he decided to take a 3 week vacation. :(


CBC PERFORMANCE

use to be grace89SS
89gt 3.8scII to much to list.
87 iroc-z the old girl is getting a make over!
90 gtz bring her back to her glory days but even better!
02 TA moser 12 bolt,yank 4k stall, spohn everything, LPE heads,MS4 cam,fast90/90 ported, hooker lt sc.
68 firebird

User avatar
fastlane02
Registered User
Posts: 315
Joined: Tue Nov 06, 2007 10:00 pm
Location: Warren, IN

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby fastlane02 » Mon Mar 10, 2008 10:22 pm

if your done and have no other info i say pin this b*tch :banana


CBC PERFORMANCE

use to be grace89SS
89gt 3.8scII to much to list.
87 iroc-z the old girl is getting a make over!
90 gtz bring her back to her glory days but even better!
02 TA moser 12 bolt,yank 4k stall, spohn everything, LPE heads,MS4 cam,fast90/90 ported, hooker lt sc.
68 firebird

User avatar
Chazzman
Registered User
Posts: 280
Joined: Thu Jun 28, 2001 8:55 pm
Location: Hillsdale Michigan
Contact:

Upgrade To 12" Front Brakes & Dual Piston Calipers

Postby Chazzman » Tue Mar 11, 2008 8:44 am


(heavywoody @ Mar. 09 2008,20:26)
QUOTE
Yeah, I know... I have other things to finish up first though. That will probably wait til next winter.

The F-bodies have more clearance since the ribbing doesn't extend across the top of the caliper... so those thinking about doing this with aftermarket 16" wheels should probably look at those calipers.

Thats what I'm hoping. I really don't want to go to a 17" wheel. Track tires are a lot more $$$.....


'92 GT-Z 3.1L 5spd lot's of GO FAST stuff  :banana

User avatar
yellow3800
Registered User
Posts: 255
Joined: Tue Jan 15, 2002 10:00 am
Location: Maryville, TN
Been thanked: 1 time
Contact:

Re: Upgrade To 12

Postby yellow3800 » Mon Nov 09, 2009 6:27 pm

Beautiful. and I can't think of a better upgrade.

How do these compare to cadillac sts front brakes? [they also 12", not aluminum maybe?]

andy
lemon <--5x115
10" front rotors,
pontiac 6000 10.5" rear rotors [or are they 10"? lol]



User avatar
99GaGT3X00
Registered User
Posts: 803
Joined: Tue Jan 11, 2005 1:56 pm
Location: North Brookfield,MA
Contact:

Re: Upgrade To 12

Postby 99GaGT3X00 » Mon Nov 09, 2009 7:49 pm

you can prob add this too if you want.

the stock N-body rotors are 13.5lbs.

for the people that dont want to go f-body brakes but want a bigger brake setup could use the N-body rotors and calipers. they are 1" bigger than the stock L-body stuff.

just another option out there for those that may not want the full f-body stuff. just substitute the f-body calipers and rotors with the grand am ones.


Image
3400/3500 Hybrid
227/233@.050 .515.515 lift 112LSA
15.232@88.85mph on stock 3400

99 Grand Am GT------03 Subaru Outback H6

User avatar
Money pit Beretta
Registered User
Posts: 6360
Joined: Thu Jul 26, 2007 11:36 am
Location: Kansas
Has thanked: 2 times
Been thanked: 9 times

Re: Upgrade To 12

Postby Money pit Beretta » Mon Nov 09, 2009 7:58 pm

Does the N body have drums in the rear?


keep'em flying!

User avatar
Cliff8928
Administrator
Posts: 1774
Joined: Wed Mar 03, 2004 10:03 pm
Location: Long Grove, IL
Has thanked: 8 times
Been thanked: 10 times
Contact:

Re: Upgrade To 12

Postby Cliff8928 » Mon Nov 09, 2009 11:07 pm

They were available both ways.


Cliff Scott
Image

User avatar
Money pit Beretta
Registered User
Posts: 6360
Joined: Thu Jul 26, 2007 11:36 am
Location: Kansas
Has thanked: 2 times
Been thanked: 9 times

Re: Upgrade To 12

Postby Money pit Beretta » Tue Nov 10, 2009 9:24 am

That would be great if the drums are also larger. I guess that there would be a need to change the spindles up front. I may give up on this idea for now. I'm a little too deep into other things. If the struts are the same I may do this later.


keep'em flying!

User avatar
99GaGT3X00
Registered User
Posts: 803
Joined: Tue Jan 11, 2005 1:56 pm
Location: North Brookfield,MA
Contact:

Re: Upgrade To 12

Postby 99GaGT3X00 » Tue Nov 10, 2009 10:18 am

like Cliff said they are available in both ways.
most SE's got drums and all GT's got rear discs.
you are aware the 99-05 N-body is 5x115 bolt pattern right.

you would be better off doing the neon rear disc swap.


Image
3400/3500 Hybrid
227/233@.050 .515.515 lift 112LSA
15.232@88.85mph on stock 3400

99 Grand Am GT------03 Subaru Outback H6


Return to “Suspension and Brakes”

Who is online

Users browsing this forum: No registered users and 3 guests