Quad4 cams cant find them on?
Quad4 cams cant find them on?
i cant find any of these cams on the difrent cam manufactures web sights could some body give me a link or something?
Cam Lift Duration
===========================
W41 .410 .219
W41#2(hot cams) .410 .241
Crane Compucam .430 .222
Crower cams .346 .224
Cam Lift Duration
===========================
W41 .410 .219
W41#2(hot cams) .410 .241
Crane Compucam .430 .222
Crower cams .346 .224
- conlinj
- Registered User
- Posts: 7
- Joined: Sun Oct 28, 2001 4:28 pm
- Location: Philadelphia PA
- Contact:
Quad4 cams cant find them on?
I called crane before and the don't make them anymore they said they ran out of cores, they said they could regrind the factory cams.  Comp cams makes them and the specs are:
  SPEC CARD
 PART #: 53-000-5I   &   53-000-5E
 ENGINE: QUAD 4CYL
GRINDING INSTRUCTIONS 1
 ""     ""    2
GRIND #: Q4E 9010 /9010  S 110.0
SPC INST 1:
SPC INST 2:
J. DIAM: STD   INT   EXH
VALVE ADJUSTMENT  .004  .004
GROSS VALVE LIFT  .000   .000
DURATION @   .050
  TAPPET LIFT  212   212
VALVE TIMING   OPEN  CLOSE
 @ .050   INT   3-   36
      EXH   36    3-
SPECS FOR CAM INST. @  110 CENTERLINE
          INT   EXH
DURATION @  .050   212.03  212.03
   LOBE LIFT   .410   .410
LOBE SEPARATION     110.0
ROCKER ARM RATIO
When i filled out the request sheet i told them that i wanted more low end power which would explain the lower duration then the w41's, they might have other grinds depending on the power band you want.
  SPEC CARD
 PART #: 53-000-5I   &   53-000-5E
 ENGINE: QUAD 4CYL
GRINDING INSTRUCTIONS 1
 ""     ""    2
GRIND #: Q4E 9010 /9010  S 110.0
SPC INST 1:
SPC INST 2:
J. DIAM: STD   INT   EXH
VALVE ADJUSTMENT  .004  .004
GROSS VALVE LIFT  .000   .000
DURATION @   .050
  TAPPET LIFT  212   212
VALVE TIMING   OPEN  CLOSE
 @ .050   INT   3-   36
      EXH   36    3-
SPECS FOR CAM INST. @  110 CENTERLINE
          INT   EXH
DURATION @  .050   212.03  212.03
   LOBE LIFT   .410   .410
LOBE SEPARATION     110.0
ROCKER ARM RATIO
When i filled out the request sheet i told them that i wanted more low end power which would explain the lower duration then the w41's, they might have other grinds depending on the power band you want.
Jim Conlin
1986 Camaro Z28
1986 Firebird Formula
1988 Monte Carlo LS
2007 Trailblazer SS
Looking for another GTZ
1986 Camaro Z28
1986 Firebird Formula
1988 Monte Carlo LS
2007 Trailblazer SS
Looking for another GTZ
Quad4 cams cant find them on?
With Quad 4's it's upper ban power you want, not low end torque.... you would be faster off the line, but slower in the end....
Quad4 cams cant find them on?
i want the w41 cams but i dont want to buy them from mantapart because they are 450 bucks and thats way over priced for me i just wantend to look for a company that sells them for cheaper
Quad4 cams cant find them on?
Quote (gtzberetta @ Mar. 10 2003,16:09)i want the w41 cams but i dont want to buy them from mantapart because they are 450 bucks and thats way over priced for me i just wantend to look for a company that sells them for cheaper
GM sold them for $500 a stick....$1000 a pair.
GM sold them for $500 a stick....$1000 a pair.
1990 Beretta GTZ 1995 Beretta Z26 1996 Beretta Z26
-
- Registered User
- Posts: 46
- Joined: Sat Oct 13, 2001 2:59 pm
- Location: Bay City, Michigan
Quad4 cams cant find them on?
If you want them bad enough, you'll pay the $450 to get them.
-Bryan
1989 Beretta GT (Money pit #1)
1996 GMC Sonoma (Money pit #2)
1993 GTZ ( Couldn't ask for a better Car)
The 3 reasons why I'm broke
1989 Beretta GT (Money pit #1)
1996 GMC Sonoma (Money pit #2)
1993 GTZ ( Couldn't ask for a better Car)
The 3 reasons why I'm broke
Quad4 cams cant find them on?
W41 cams off of gmpartsdirect.
Part # unit price S&H
24572402 $203.47 $40.69
24572403 $203.47 $40.69
I dont know why S&H is so much on them. I hope its a mistake.
Part # unit price S&H
24572402 $203.47 $40.69
24572403 $203.47 $40.69
I dont know why S&H is so much on them. I hope its a mistake.
Quad4 cams cant find them on?
That’s some what of a better price becides shiping. What’s the spec of the w41 cams .410 lift 218 degrees duration??? dose gmpd sell cam blanks??
Quad4 cams cant find them on?
gmpd has high shipping costs because they have low prices...which was the explaination that i got from one of their reps...heh.
Quad4 cams cant find them on?
That’s reasonable explanation I guess
Quad4 cams cant find them on?
this is the email i got from comp cams these are w41 cams
Hello, the part number you are looking for is a 53-000-5I w/ a
grind number of 9011/9011
that is an intake camshaft. You will also need a exhaust camshaft
53-000-5E w/ a grind number of 9011/9011
I would recommend installing these on a 112 lobe
separation.
I have included 2 spec cards below. These
cams are $194.98 ea.
Thanks,
Hadley
SPEC CARD
PART #: 53-000-5I
ENGINE: QUAD 4CYL
GRINDING INSTRUCTIONS 1
"" "" 2
GRIND #: Q4I 9011 /9011 S 112.0
SPC INST 1:
SPC INST 2:
J. DIAM: STD INT EXH
VALVE ADJUSTMENT .004 .004
GROSS VALVE LIFT .000 .000
DURATION @ .050
TAPPET LIFT 216 216
VALVE TIMING OPEN CLOSE
@ .050 INT 2- 37
EXH 41 6-
SPECS FOR CAM INST. @ 110 CENTERLINE
INT EXH
DURATION @ .050 215.74 215.74
LOBE LIFT .410 .410
LOBE SEPARATION 112.0
ROCKER ARM RATIO REQ S
Hello, the part number you are looking for is a 53-000-5I w/ a
grind number of 9011/9011
that is an intake camshaft. You will also need a exhaust camshaft
53-000-5E w/ a grind number of 9011/9011
I would recommend installing these on a 112 lobe
separation.
I have included 2 spec cards below. These
cams are $194.98 ea.
Thanks,
Hadley
SPEC CARD
PART #: 53-000-5I
ENGINE: QUAD 4CYL
GRINDING INSTRUCTIONS 1
"" "" 2
GRIND #: Q4I 9011 /9011 S 112.0
SPC INST 1:
SPC INST 2:
J. DIAM: STD INT EXH
VALVE ADJUSTMENT .004 .004
GROSS VALVE LIFT .000 .000
DURATION @ .050
TAPPET LIFT 216 216
VALVE TIMING OPEN CLOSE
@ .050 INT 2- 37
EXH 41 6-
SPECS FOR CAM INST. @ 110 CENTERLINE
INT EXH
DURATION @ .050 215.74 215.74
LOBE LIFT .410 .410
LOBE SEPARATION 112.0
ROCKER ARM RATIO REQ S
Quad4 cams cant find them on?
Then add another $200 to have them ground. I was quoted $125 A CAM to have the W41 cams I have redone...