Well I FINALLY broke it!
-
- Registered User
- Posts: 40
- Joined: Mon May 25, 2009 11:31 pm
Re: Well I FINALLY broke it!
3400beretta wrote:I didn't even think to tape it.. pisses me off. I'll post some time slips on the weekend when I'm back home though..
That's what you get when you guys go racing without me...NO VIDEO...lol.
Congrats Rodney...sorry I missed it.
- woody90gtz
- Registered User
- Posts: 4703
- Joined: Thu Jul 11, 2002 8:45 pm
- Location: Walton, NY
- Contact:
Re: Well I FINALLY broke it!
Congrats! Took you long enough to break it! haha
I'm sure it will end up being better than it was anyway. Going to go with some Driveshaft Shop axles?
I'm sure it will end up being better than it was anyway. Going to go with some Driveshaft Shop axles?
91 "SS" - WOT 3400/5spd - 13.29@101.6 - World's fastest N/A FWD Beretta
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
- Asylum
- Registered User
- Posts: 3050
- Joined: Wed Mar 31, 2004 9:36 am
- Location: Hamilton, Ontario, Canada
- Contact:
Re: Well I FINALLY broke it!
Nope!
It was the situation that broke it, not the parts.
I am of the opinion it would have broken damn near any axle with what happened.
Basically it free-wheeled to the shift light, I let off to zero, it grabbed, and SNAP!
Axles shouldn't break on these cars if everything is aligned correctly, but I suppose you can only expect so much.
This was not as much a part failure as a failure of a part that had no chance given what happened.
But it'll be fixed in a couple of days.
HELL Rodney just ran mid 12's at 118 on stock axles with a 5-speed. I certainly don't need $700+ worth of axles!!
It was the situation that broke it, not the parts.
I am of the opinion it would have broken damn near any axle with what happened.
Basically it free-wheeled to the shift light, I let off to zero, it grabbed, and SNAP!
Axles shouldn't break on these cars if everything is aligned correctly, but I suppose you can only expect so much.
This was not as much a part failure as a failure of a part that had no chance given what happened.
But it'll be fixed in a couple of days.
HELL Rodney just ran mid 12's at 118 on stock axles with a 5-speed. I certainly don't need $700+ worth of axles!!
Eric
Asylum Motorsports
"Where we're not happy 'til YOU'RE not happy!
'91 California Quad (Gone with just a bit of "Seller's Remorse".)
'92 3500 GT gone and not really missed. It was fun. Documented 13.47 N/A.
Asylum Motorsports
"Where we're not happy 'til YOU'RE not happy!
'91 California Quad (Gone with just a bit of "Seller's Remorse".)
'92 3500 GT gone and not really missed. It was fun. Documented 13.47 N/A.
- IsaacHayes
- Registered User
- Posts: 975
- Joined: Fri Oct 07, 2005 8:32 pm
- Location: Missouri
Re: Well I FINALLY broke it!
Stock axles are stronger than aftermarket, just keep that in mind.
Rodney, we want video because we want to be entertained!!! I heard something about your 3500 breaking, was that not true?
Rodney, we want video because we want to be entertained!!! I heard something about your 3500 breaking, was that not true?
- 3400beretta
- Registered User
- Posts: 281
- Joined: Fri Mar 10, 2006 2:21 am
Re: Well I FINALLY broke it!
Yes its true.. new engine is in already. The old engine was hurt, it overheated a couple times, and had low (125psi) compression in 1 cylinder. Plus I had an ignition related issue, it would sputter and backfire under load - at first just WOT, but then it got worse. It took me awhile to figure out what the problem was, it turned out to be a bad ignition module. I suspected the ignition module right off the bat, and swapped it with my spare, but the car did the exact same thing. So I figured it was something else - it wasn't till I tried the one from my grand am, that the problem went away, so I guess I had 2 bad ignition modules, which I find very strange.
Anyways, that sputtering/backfiring is what did the engine in, I was at the track, and I didn't let off the gas when it started doing it, mostly because I was frustrated, and I knew the engine was junk/coming out anyways. So lesson learned - fucked up ignition timing + 14 PSI = multiple connecting rod failures!
Anyways, that sputtering/backfiring is what did the engine in, I was at the track, and I didn't let off the gas when it started doing it, mostly because I was frustrated, and I knew the engine was junk/coming out anyways. So lesson learned - fucked up ignition timing + 14 PSI = multiple connecting rod failures!
- IsaacHayes
- Registered User
- Posts: 975
- Joined: Fri Oct 07, 2005 8:32 pm
- Location: Missouri
Re: Well I FINALLY broke it!
Broke or bent rods? That's at least different from the usual melted/shattered pistons!
Re: Well I FINALLY broke it!
You can take out 2 pistons and a rod and a block with 1 single hose clamp screw. Why play with turbos?
Good thing is that flying crap from inside the motor didnt take out the turbo... that woulda sucked!
Good thing is that flying crap from inside the motor didnt take out the turbo... that woulda sucked!
- 3400beretta
- Registered User
- Posts: 281
- Joined: Fri Mar 10, 2006 2:21 am
Re: Well I FINALLY broke it!
No, they were MIA. I should have taken pics I guess.. A few (very) small pieces of one connecting rod were in the oil pan, and the big end of one connecting rod was attached to the crank still. Both pistons (5 & 6) were just up in the cylinders with NOTHING attached to them. Some how the other connecting rod removed itself from the crank journal, and also removed a counterweight from this FORGED crank. I had 3 holes in the oil pan, 2 bigger than my fist, the 3rd was right behind my starter, which a piece of connecting rod so kindly cracked my mini starter. The block was cracked on both sides, near cylinders 5 & 6. However, the tops of all the pistons were perfect still, no nicks, hot spots or otherwise evidence of detonation.
- 3X00-Modified
- Administrator
- Posts: 10912
- Joined: Thu Jul 05, 2007 9:18 am
- Location: Brooklyn CT
Re: Well I FINALLY broke it!
Nice carnage...3400beretta wrote:No, they were MIA. I should have taken pics I guess.. A few (very) small pieces of one connecting rod were in the oil pan, and the big end of one connecting rod was attached to the crank still. Both pistons (5 & 6) were just up in the cylinders with NOTHING attached to them. Some how the other connecting rod removed itself from the crank journal, and also removed a counterweight from this FORGED crank. I had 3 holes in the oil pan, 2 bigger than my fist, the 3rd was right behind my starter, which a piece of connecting rod so kindly cracked my mini starter. The block was cracked on both sides, near cylinders 5 & 6. However, the tops of all the pistons were perfect still, no nicks, hot spots or otherwise evidence of detonation.
I have a piston on my PC from one of our last rules motors that we ran at Thompson Speedway... The wrist pin pulled right out the bottom of the piston and the rod made its way around the block destroying everything in in its path, yet the piston was just sitting there at the top of the bore. I removed the piston from the hole in the side of the block, that's how bad it was... LOL
- 3400beretta
- Registered User
- Posts: 281
- Joined: Fri Mar 10, 2006 2:21 am
Re: Well I FINALLY broke it!
Here ya go.. on the left (9037)
On the 12.52 slip, the guy in the right lane was a magnum with quite a bit of work done to his car.. needless to say, he was pretty pissed off.. haha.
On the 12.52 slip, the guy in the right lane was a magnum with quite a bit of work done to his car.. needless to say, he was pretty pissed off.. haha.
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
Re: Well I FINALLY broke it!
Man is that fast! Yeah I bet he about craped him self in anger.
keep'em flying!
- Asylum
- Registered User
- Posts: 3050
- Joined: Wed Mar 31, 2004 9:36 am
- Location: Hamilton, Ontario, Canada
- Contact:
Re: Well I FINALLY broke it!
I was there, and the guy in the Magnun (nice car with a few mods!) is STILL trying to figure out what the hell that was all about. LOL!!
Rodney's car is scary!
Rodney's car is scary!
Eric
Asylum Motorsports
"Where we're not happy 'til YOU'RE not happy!
'91 California Quad (Gone with just a bit of "Seller's Remorse".)
'92 3500 GT gone and not really missed. It was fun. Documented 13.47 N/A.
Asylum Motorsports
"Where we're not happy 'til YOU'RE not happy!
'91 California Quad (Gone with just a bit of "Seller's Remorse".)
'92 3500 GT gone and not really missed. It was fun. Documented 13.47 N/A.