z26 problems
z26 problems
im having problems with my z26 still. to those of you that remeber me from bstuff i have been having problems with this thing for while ... it is ideling really rough and spits and sputters all the time when you get on it or are just regular driving it. i have replaced a long list of things and still seems to not run right.
things i have done are
both crank sensors
cam sensor
new o2 sensor
new coils and icm
both sensors on throttle body
new plugs and wires
new upper intake gaskets
new fuel pressure regulator injector orings and deep cleaned the injectors
i have no idea what this could be besides the computer, does anyone no what else it can be i hate to keep putting money into things that it isnt. also if anyone has a link to a way to check the check engine light codes on it bc its a 95 and the locals stores dont hold a dyognostics computer for the obd1
things i have done are
both crank sensors
cam sensor
new o2 sensor
new coils and icm
both sensors on throttle body
new plugs and wires
new upper intake gaskets
new fuel pressure regulator injector orings and deep cleaned the injectors
i have no idea what this could be besides the computer, does anyone no what else it can be i hate to keep putting money into things that it isnt. also if anyone has a link to a way to check the check engine light codes on it bc its a 95 and the locals stores dont hold a dyognostics computer for the obd1
Re: z26 problems
Have you even looked at the computer? Its in a retarded location. The air inlet for the heater system is right above it, and thats obviosly open to the elements under the black plastic vent cover on the outside of the car. The only thing that keeps water out of the car there is a shitty rubber seal under that vaccum solinoid for the heater. If that seal is broken you have water dripping down basically right over the computer.
I suggest just physically looking at the computer for corrosion/etc.
I suggest just physically looking at the computer for corrosion/etc.
My Motortopia
Bfest Committee 2012, 2013, 2014
Bfest AND Bust 2012 Winner: First ever clutch swap at Berettafest!
Bfest 2013 Watermelon Award: Boob shaped hood dents FTW
- woody90gtz
- Registered User
- Posts: 4703
- Joined: Thu Jul 11, 2002 8:45 pm
- Location: Walton, NY
- Contact:
Re: z26 problems
If you know anyone local with an ALDL cable and software like TunerPro RT you can check the codes yourself. In a pinch you can also try the paper clip trick by jumping two of the ALDL port pins and counting the flashes of the SES light. Then you just need to find out what the code number is for.
91 "SS" - WOT 3400/5spd - 13.29@101.6 - World's fastest N/A FWD Beretta
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
Re: z26 problems
Can you jumper a 95 ecm?
My Motortopia
Bfest Committee 2012, 2013, 2014
Bfest AND Bust 2012 Winner: First ever clutch swap at Berettafest!
Bfest 2013 Watermelon Award: Boob shaped hood dents FTW
- 3X00-Modified
- Administrator
- Posts: 10912
- Joined: Thu Jul 05, 2007 9:18 am
- Location: Brooklyn CT
Re: z26 problems
No, it talks like OBDI but its programmed and designed like OBDII so there is only one wire going to the com port, plus a power wire IIRC.
Woody... Were you ever able to jumper your 95? That only works on 93 and older berettas. Look at the Com plug the two wires your supposed to jumper don't exist.
Woody... Were you ever able to jumper your 95? That only works on 93 and older berettas. Look at the Com plug the two wires your supposed to jumper don't exist.
-
- Registered User
- Posts: 1035
- Joined: Thu Feb 20, 2003 11:21 pm
- Location: South Central MN
Re: z26 problems
You can check the ohms on all the injectors, shouldn't be any below 10. Otherwise, a scanner is the best bet. A compression test might be a good idea also.
94 Beretta Z26 57,4xx miles
3100, auto, crank windows, power locks/trunk, A/C,
To many mods to list
-intercooler
Among beretta boards
1st Turbo 4t60-e
1st Turbo 3100
1st Turbo Z26
1st 94+ Turbo
3100, auto, crank windows, power locks/trunk, A/C,
To many mods to list
-intercooler
Among beretta boards
1st Turbo 4t60-e
1st Turbo 3100
1st Turbo Z26
1st 94+ Turbo
-
- Registered User
- Posts: 1068
- Joined: Sun Nov 02, 2003 11:54 am
- Location: Paulden, AZ
- Contact:
Re: z26 problems
Sounds like the typical bad O2 sensor, check it out and replace it, bet it helps 100%
Geoff
95 Base V6: Current Project; Work In Progress
95 Base V6: Current Project; Work In Progress
Re: z26 problems
well still having troubles, got a new o2 sensor coils icm and computer this weekend and nothing yet, does anyone have any more sugestions.. need to fix this asap or its goin to the crusher
-
- Registered User
- Posts: 181
- Joined: Thu Apr 15, 2010 8:51 pm
Re: z26 problems
mine did the same thing n it was the fuel pump. check n see what ur pressure is if it is below 30psi u need a new pump
3 speed auto to a 5 speed manual
Body kit going on soon
1993 Beretta GT
Body kit going on soon
1993 Beretta GT
Re: z26 problems
Or the filter is plugged up. lol
94' Z26 Project - 95' Base Project - Custom LED Light Conversions!
Chosen Proposal Submission & Committee Member for Beretta Fest 2012 in Traverse City Michigan
Chosen Proposal Submission & Committee Member for Beretta Fest 2012 in Traverse City Michigan
-
- Registered User
- Posts: 181
- Joined: Thu Apr 15, 2010 8:51 pm
Re: z26 problems
that 2 lmao how could i for get that
3 speed auto to a 5 speed manual
Body kit going on soon
1993 Beretta GT
Body kit going on soon
1993 Beretta GT
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
Re: z26 problems
Wow you changed all that and not the MAP. Or is it a 96? That would be both MAP and MAF right?
2nd on the fuel filter. Did you Sea Foam down the booster? Could have a huge carbon build up. Hope your running AC plugs. Others can cause problems.
2nd on the fuel filter. Did you Sea Foam down the booster? Could have a huge carbon build up. Hope your running AC plugs. Others can cause problems.
keep'em flying!
Re: z26 problems
map sensor i did change it does have the maf tho the fuel filter is new and changed and i honestly havent checked the pump yet but im gonna look into it now. i did run booster but didnt ever seafoam it down, i honestly didnt think anything of it.
Re: z26 problems
ok i got a fuel pump pressure tester and it showed up that it was way over presured the thing it led down to is either a pump or a fuel pressure regulator i have changed the regultor before with a good used one but it hasnt seemed to help, does anyone no anything i can try before i go and tear out the pump