1991 Gauge Cluster vs. 1995 Gauge Cluster

If there isn't a place for your question then put it here.
dezenzerrick
Posts: 4
Joined: Sat Jan 07, 2017 10:49 pm

1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby dezenzerrick » Sat Jan 07, 2017 11:07 pm

Hi All,

Looking to do a gauge cluster swap from base to the Z26 or GTU (something with a tachometer).
I'm not really able to find a 94-95 available, but I noticed that the 91 looks very similar to the 95 both physically, in the way they mount up, and the electrical connector looks the same. Does anyone have a wiring diagram for the 91? Just as a comparison, I have a couple of photos as well of the rear of each cluster, attached below.

Thanks!

95 base:
95 base cluster.jpg


91 w/ Tach
91 cluster.jpg



User avatar
themixer
Registered User
Posts: 1516
Joined: Fri Aug 14, 2009 12:13 pm
Location: Truro, Nova Scotia. Canada
Has thanked: 3 times
Been thanked: 16 times

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby themixer » Thu Jan 12, 2017 1:28 pm

you need the full cluster from 94-95 its obd 1.5. Someone on this board must have one they can sell you!



User avatar
woody90gtz
Registered User
Posts: 4032
Joined: Thu Jul 11, 2002 8:45 pm
Location: Walton, NY
Has thanked: 4 times
Been thanked: 7 times
Contact:

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby woody90gtz » Thu Jan 12, 2017 7:08 pm

I don't think he does. I replaced my partially dead 91 cluster with the one out of my 95 and it was a direct swap. That's opposite from a 91 cluster in a 95, but I think it would be fine.


Image
91 "SS" 3400/5spd - EP, FFP, TCE, SPEC, DSS, S&S, OBD1, 13s? GEARHEAD dezign

User avatar
themixer
Registered User
Posts: 1516
Joined: Fri Aug 14, 2009 12:13 pm
Location: Truro, Nova Scotia. Canada
Has thanked: 3 times
Been thanked: 16 times

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby themixer » Fri Jan 13, 2017 9:02 am

give it a rip and see what happens!



JeffD
Registered User
Posts: 467
Joined: Tue Feb 07, 2006 9:44 pm
Location: new york

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby JeffD » Sun Jan 15, 2017 6:12 pm

I just removed my 94 cluster for a digital panel swap.

Sent from my MotoG3 using Tapatalk


1988 Beretta GT 5 speed - 1st car... Gone to the crusher. :(
1989 Beretta GT Z-51
1994 Beretta Z26 getting FE7+Z51 goodies
1987 Pontiac Bonneville LG3+4T65-E
1987 Chevrolet Celebrity Wagon L36+4T65-E
1998 Chevrolet C1500 5.7L L31+ built 4L60-E

JeffD
Registered User
Posts: 467
Joined: Tue Feb 07, 2006 9:44 pm
Location: new york

Re: RE: Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby JeffD » Sun Jan 15, 2017 6:13 pm

JeffD wrote:I just removed my 94 cluster for a digital panel swap. It's for sale, pm me if interested.

Sent from my MotoG3 using Tapatalk




Sent from my MotoG3 using Tapatalk


1988 Beretta GT 5 speed - 1st car... Gone to the crusher. :(
1989 Beretta GT Z-51
1994 Beretta Z26 getting FE7+Z51 goodies
1987 Pontiac Bonneville LG3+4T65-E
1987 Chevrolet Celebrity Wagon L36+4T65-E
1998 Chevrolet C1500 5.7L L31+ built 4L60-E

dezenzerrick
Posts: 4
Joined: Sat Jan 07, 2017 10:49 pm

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby dezenzerrick » Mon Jan 16, 2017 7:55 pm

Thanks! I'll let you guys know how it goes. I've managed to find a few 91's on the web, they are rare but still around.
Worst comes to worst, I can always sell the gauge cluster I bought if it doesn't work!



User avatar
3X00-Modified
Administrator
Posts: 10657
Joined: Thu Jul 05, 2007 9:18 am
Location: Plainfield CT
Has thanked: 12 times
Been thanked: 46 times

Re: 1991 Gauge Cluster vs. 1995 Gauge Cluster

Postby 3X00-Modified » Wed Jan 18, 2017 9:36 am

The only year specific cluster is 96, and you can actually use a older cluster in the 96 if you really needed to... you would just have to re-wire the Tach signal to come from the ICM and not the ECU.




Return to “General Questions”

Who is online

Users browsing this forum: No registered users and 3 guests