My Dyno Run video
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact:
My Dyno Run video
Hey i thought i would post my dyno run from sunday the mustang dyno says it only has 101 HP i find that quite low for a v-6 with higher compression pistons
DYNO run
DYNO run
-
- Registered User
- Posts: 720
- Joined: Wed Apr 25, 2001 5:39 pm
- Location: Shelbina, MO
- Contact:
My Dyno Run video
*** are they doing with your car? It sure wasn't a dyno run.
Rex Weatherford
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact:
My Dyno Run video
no im not holding anything back im just shocked that it says that i only have 101 HP and 133ft LBS and thats it
-
- Registered User
- Posts: 720
- Joined: Wed Apr 25, 2001 5:39 pm
- Location: Shelbina, MO
- Contact:
My Dyno Run video
Why does that suprise you?  Mustang dynos usually read a little lower than a dynojet. Do you have a chart to post so that we can give some type of suggestions?
Your car was factory rated 140 HP and 180 Ft-lbs.  You have an auto tranny.
Pauls 2.8L Turbo 5-Speed only made about 155 WHP with 6 PSI. ÂÂÂ
I don't have any 3.1L dynos.  But it doesn't really suprise me if you have not done any head or cam work.  I'm not too sure what they should run, but Mustangs generally would read less than what we dynoed on a BFest.
Your car was factory rated 140 HP and 180 Ft-lbs.  You have an auto tranny.
Pauls 2.8L Turbo 5-Speed only made about 155 WHP with 6 PSI. ÂÂÂ
I don't have any 3.1L dynos.  But it doesn't really suprise me if you have not done any head or cam work.  I'm not too sure what they should run, but Mustangs generally would read less than what we dynoed on a BFest.
Rex Weatherford
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
My Dyno Run video
(rweatherford @ May 23 2007,22:47)QUOTEWhy does that suprise you? Mustang dynos usually read a little lower than a dynojet. Do you have a chart to post so that we can give some type of suggestions?
Your car was factory rated 140 HP and 180 Ft-lbs. You have an auto tranny.
Pauls 2.8L Turbo 5-Speed only made about 155 WHP with 6 PSI.
I don't have any 3.1L dynos. But it doesn't really suprise me if you have not done any head or cam work. I'm not too sure what they should run, but Mustangs generally would read less than what we dynoed on a BFest.
I think Aaron Choate had a dyno of his 3.1 5spd with I think just chip or just intake and it made something like 120whp and 177tq.
A bone stock 3.1 auto should put down about 105-110whp on a Mustang dyno.
The whp may not be that suspect on this dyno but the tq sure is. Bone stock it should be 150 at the very least with 165-170 being more likely.
I have had a few dyno by now and this looked like they had no idea what they were doing.
91' GT  SOLD
99' Saab Viggen Stg-4 315hp- in European Car Magazine  7/2006
99' Saab Viggen Stg-4 315hp- in European Car Magazine  7/2006
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact:
-
- Registered User
- Posts: 1035
- Joined: Thu Feb 20, 2003 11:21 pm
- Location: South Central MN
My Dyno Run video
were talking a 3.1L correct? not a 3100? A 3.1 on a mustang usually doesnt barely make it to 100 hp with an auto.
I would not trust that dyno reading at all. Seems as if they had no idea how to dyno a FWD auto.
I would not trust that dyno reading at all. Seems as if they had no idea how to dyno a FWD auto.
94 Beretta Z26 57,4xx miles
3100, auto, crank windows, power locks/trunk, A/C,
To many mods to list
-intercooler
Among beretta boards
1st Turbo 4t60-e
1st Turbo 3100
1st Turbo Z26
1st 94+ Turbo
3100, auto, crank windows, power locks/trunk, A/C,
To many mods to list
-intercooler
Among beretta boards
1st Turbo 4t60-e
1st Turbo 3100
1st Turbo Z26
1st 94+ Turbo
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact:
My Dyno Run video
yes i have a 3.1 very slightly built all i have done is bored 0.040 over and higher compression pistons and that is also on a streched timing chain.
- pontiac3100
- Registered User
- Posts: 19
- Joined: Sun Apr 22, 2007 8:39 pm
- Location: chi-town
My Dyno Run video
umm someone correct me if i'm wrong i noticed on hp tv they floor it.
and the person that was driving it did'nt open it up .
i had a gtz auto and she had some get up...
but yours sounds and looks tite.
and the person that was driving it did'nt open it up .
i had a gtz auto and she had some get up...
but yours sounds and looks tite.
- KFLO 93 GT
- Registered User
- Posts: 846
- Joined: Thu Jul 25, 2002 2:46 am
- Location: Iowa
- Contact:
My Dyno Run video
Wow, .040 overbore... that's a ******* lot. Then no supporting mods... did it occur to you to do a cam, some headwork, porting the craptastic intake manifolds maybe...? .040 over is a lot man...
93 GTs
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact:
My Dyno Run video
well the idiot who rebuilt the block last didnt check check piston clearance and well when i put it in it lasted for a little bit then the skirt on one busted off while it was running and then i parked it and pulled the engine and to bring it back within spec .040 was the closest i could do but fear not at this point the pistons have about .0015 between the walls and pistons so no slap now and she still runs like a champ! starts on those below zero days no problem! i have two 3.1's on the side those are going to be the crazy mod engines im going to crank HP out of those two.
-
- Registered User
- Posts: 720
- Joined: Wed Apr 25, 2001 5:39 pm
- Location: Shelbina, MO
- Contact:
My Dyno Run video
If you want much HP out of them you will have to make a new intake manifold for them. The factory one is too small. The other option is to win the Extrude Hone manifold treatment at BFest or pay them to do a factory manifold.
Norm had this done and I can't remember how much HP he gained, but it was significant.
Norm had this done and I can't remember how much HP he gained, but it was significant.
Rex Weatherford
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
92 Beretta GTZ Quad4 Turbo / 5-speed (sold)
Best 1/4 ET =  13.523 @ 105.16 mph
07 Mazda 5 Black on Black (it's slow)
- berettajunkie1991
- Registered User
- Posts: 217
- Joined: Sat Jul 16, 2005 1:40 am
- Location: Illinois
- Contact: