Search found 389 matches
- Wed Apr 13, 2016 9:04 pm
- Forum: General Discussion
- Topic: Motor mounts?
- Replies: 2
- Views: 2302
Motor mounts?
Does 96 Mounts fit on a 93 Beretta?
Can I put a 4t60 (non-e) in place of the 3t40?
Can I put a 4t60 (non-e) in place of the 3t40?
- Sun Jan 31, 2016 10:04 am
- Forum: Drag Racing, Auto-x and Track events
- Topic: Beretta 1/4 mile times
- Replies: 157
- Views: 179363
Re: Beretta 1/4 mile times
Thanks for posting this list, it gives me an idea what to expect.
- Sun Dec 20, 2015 4:58 pm
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
Unplugged the MAF and readjusted the pins and it doesn't seem to throw any MAP codes anymore.
No more stalling on a warm/hot start.
I'll have to test it some more to make sure the revving stopped for good.
No more stalling on a warm/hot start.
I'll have to test it some more to make sure the revving stopped for good.
- Wed Dec 16, 2015 8:40 pm
- Forum: General Discussion
- Topic: What muffler would you buy?
- Replies: 3
- Views: 4748
What muffler would you buy?
I am looking for a muffler with good air flow on a 90 Beretta
- Tue Dec 08, 2015 11:25 am
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
I havent had time to check the maf plug to make sure its good.
Or blocking the egr to test for it being stuck open?
I have to hold the gas pedal a bit to keep it from stalling and I hold the idle about 750 rpm.
Or blocking the egr to test for it being stuck open?
I have to hold the gas pedal a bit to keep it from stalling and I hold the idle about 750 rpm.
- Sat Dec 05, 2015 11:02 am
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
I havent had time to block off the EGR Yet, I have been really bussy, I did get time to check codes again. New development, MAF low input code 102 showed up after a week or two of the revving problem not happening. Possible the MAF was reading low enough the engine revved up to compensate and now it...
- Wed Nov 25, 2015 9:34 pm
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
Unfortunately, the IAC count is the only thing my scanner can't read.
How would a stuck open EGR cause the car to behave?
How can I check this?
How would a stuck open EGR cause the car to behave?
How can I check this?
- Tue Nov 24, 2015 11:34 am
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
I always considered them as close to oem as possible without buying dealer oem.
Car still has the problem. Showed up again.
No SES lights or codes ever when this problem happens.
Only fix is turn it off and on again.
Car still has the problem. Showed up again.
No SES lights or codes ever when this problem happens.
Only fix is turn it off and on again.
- Sat Nov 21, 2015 5:35 pm
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Re: Engine wants to rev up again, have no idea why...
We checked my car up against a known good Beretta, everything was the same. However when my problem happened sometimes it would not be 0% throttle position at 0%. It read 5% at 0% throttle.
- Fri Nov 20, 2015 7:50 pm
- Forum: Diagnostic Help
- Topic: Engine wants to rev up again, have no idea why...
- Replies: 14
- Views: 7183
Engine wants to rev up again, have no idea why...
1996 Beretta 3100 v6 automatic Replaced: Throttle position sensor (No Change). Idle air control (No Change). ECM (Problem was fixed). Engine revs up to 2800 RPM, however only if I get the car on the freeway (Typical freeway speeds 65-70 MPH). temporary fix: Put car in neutral and turn engine off, wa...
- Tue Nov 03, 2015 3:37 pm
- Forum: For Sale
- Topic: REDUCED-1990 White GTZ For Sale, South Louisiana $4400
- Replies: 57
- Views: 29186
Re: REDUCED-1990 White GTZ For Sale, South Louisiana $4400
I couldn't tell because there was a side conversation going on part way through.
- Tue Nov 03, 2015 2:45 pm
- Forum: For Sale
- Topic: REDUCED-1990 White GTZ For Sale, South Louisiana $4400
- Replies: 57
- Views: 29186
Re: REDUCED-1990 White GTZ For Sale, South Louisiana $4400
Is the car still for sale?
- Wed Oct 28, 2015 11:05 am
- Forum: General Discussion
- Topic: Can someone tell me which pins are these on the ECM?
- Replies: 5
- Views: 3320
Re: Can someone tell me which pins are these on the ECM?
Need some help if possible.
Is there something missing?
According to this it should work?
Is there something missing?
According to this it should work?
- Sat Oct 17, 2015 1:45 pm
- Forum: General Discussion
- Topic: Can someone tell me which pins are these on the ECM?
- Replies: 5
- Views: 3320
Re: Can someone tell me which pins are these on the ECM?
I saved a copy, thanks!
- Sat Oct 17, 2015 12:12 pm
- Forum: General Discussion
- Topic: Can someone tell me which pins are these on the ECM?
- Replies: 5
- Views: 3320
Re: Can someone tell me which pins are these on the ECM?
1990 Beretta 3.1 v6 automatic.Cliff8928 wrote:What year and engine?