Page 15 of 34
3800 Series III Turbo...
Posted: Fri Sep 23, 2005 1:26 pm
by nocutt
I think we will end up dumping the outlet overboard for a little power...I sincerely hope it woudn't be as noisy
Q
U
O
T
E originally posted by Puller:
I love you.
I love you too...
3800 Series III Turbo...
Posted: Fri Sep 23, 2005 3:58 pm
by HeartBeatKid
where did you get those coilovers? i want some
3800 Series III Turbo...
Posted: Fri Sep 23, 2005 5:41 pm
by nocutt
(Jdawg4201 @ Sep. 22 2005,14:58)Q
U
O
T
Ewhere did you get those coilovers? i want some
I actually got the springs thru WCF however you can find them here...
Dependent on how this things make out and interest I will seriously look into offering them thru WCF...hit me up for more details...
3800 Series III Turbo...
Posted: Sat Sep 24, 2005 2:41 am
by HeartBeatKid
i most definatly want the coilovers and i need ones for the rear to
3800 Series III Turbo...
Posted: Sun Sep 25, 2005 1:44 am
by nocutt
So spent a lil time today with the car...TLC so to speak, I managed to do the TB adapter...
3800 Series III Turbo...
Posted: Sun Sep 25, 2005 1:46 am
by nocutt
On the caro...
3800 Series III Turbo...
Posted: Sun Sep 25, 2005 1:47 am
by nocutt
Also hooked up water lines, heater source from block:
3800 Series III Turbo...
Posted: Sun Sep 25, 2005 1:51 am
by nocutt
to the Comp unit...
yeah I know funky angle
3800 Series III Turbo...
Posted: Tue Oct 04, 2005 3:08 am
by nocutt
LAST DAYS...
TLC with the adapter some more, cut the "neck" to the intake and had the adapter welded with a slight "cork"...it will be much easier making the final tb-intake piece...
3800 Series III Turbo...
Posted: Tue Oct 04, 2005 3:12 am
by nocutt
Hard to notice...the TB is slightly bent outwards (towards you) and it is also raised (towards hood)...
3800 Series III Turbo...
Posted: Tue Oct 04, 2005 3:18 am
by nocutt
Was able to complete the pre-IC pipe, I was seriously trying to avoid having the turbo outlet re-fabbed to accept the old intake...luck was on my side... this time around, measured once; then had it welded...
3800 Series III Turbo...
Posted: Tue Oct 04, 2005 3:26 am
by nocutt
And the W/G outlet dump; noisy? worth it? are the gains measurable...with this particular setup
Might be hard to see...but dump is behind rad and infront of engine...
3800 Series III Turbo...
Posted: Wed Oct 05, 2005 8:45 am
by RebelGT
I think you have 2 square inches left of space in that engine bay, good job looks nice.
3800 Series III Turbo...
Posted: Mon Oct 10, 2005 4:36 pm
by ROLNGTZ
Do you have a time frame on completion?
3800 Series III Turbo...
Posted: Mon Oct 10, 2005 6:47 pm
by nocutt
Q
U
O
T
EI think you have 2 square inches left of space in that engine bay, good job looks nice
...No ...ish Rebel, I am starting to be very afraid...again
Thanks I appreciate the kind words...you are gonna makes me cry
Roln, I unfortunately ran out of my projected completion date...ti was supposed to be before I went back to school...I wanted to use the summer...but as usual mula and time met at a place called "..ish outtluck"...lol!! I surmise I will be done no later than a month...
how is your project?