Re: Project: Slideways z26
Posted: Fri Feb 03, 2012 11:23 am
So ever get a shot of the engine from above so we can see where its placed?
Beretta.net
Official Chevrolet Beretta Owners Forums
https://www.beretta.net/forum/
Project: Slideways z26
Page 18 of 39
Re: Project: Slideways z26
Posted: Fri Feb 03, 2012 11:26 am
I'll get one. It's way too far forward IMO. Balancer is 3.5 inches from lower rad support. But that's what I had to do to use stock steering
Re: Project: Slideways z26
Posted: Fri Feb 03, 2012 2:38 pm
Is that a bad thing when drifing?
Re: Project: Slideways z26
Posted: Fri Feb 03, 2012 3:48 pm
Not at all. But it's best from a handling standpoint to have the majority of mass between the front and back axle.
More more grip you have the better for drift surprisingly
More more grip you have the better for drift surprisingly
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 7:59 am
Finished both motor mounts and the tranny crossmember. The engine is finally in the bay with no jacks or hoists holding it up. Feels good. Ill get pics soon.
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 3:14 pm
Thanks! Never knew that. I figured weight forward and little rear grip was best, but makes sense that you would want it balanced.Barry wrote:Not at all. But it's best from a handling standpoint to have the majority of mass between the front and back axle.
More more grip you have the better for drift surprisingly
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 3:40 pm
LMAO3X00-Modified wrote:There is quite a bit of rocker rust on that car IIRC, so its not a perfect shell, he will have to do many mods to keep it running let alone move to RWD so I wouldn't say it's destroying. He either does this or it gets sold off to someone who beats it into the ground or it rots away... Which do you think is better.SuzukiGhostRider wrote:I hope you're not talking about destroying the car in your avatar?
And that's a shitty leaf blower... its friken electric...
I think its a GREAT idea! Dang Burritos shoulda been RWD from the start.
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 10:24 pm
pics pics pics...........
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 10:48 pm
Haha agreed, ^ also what did you end up doing for the engine mounts? hockey pucks of 240sx mounts?
Re: Project: Slideways z26
Posted: Mon Feb 06, 2012 11:41 pm
Pucks. If I come across a set of poly 240 mounts I'll bolt them in. Pucks are so damn harsh
Re: Project: Slideways z26
Posted: Wed Feb 08, 2012 12:30 pm
Alpinestar10 wrote:So ever get a shot of the engine from above so we can see where its placed?
Re: Project: Slideways z26
Posted: Wed Feb 08, 2012 12:31 pm
Re: Project: Slideways z26
Posted: Wed Feb 08, 2012 12:58 pm
Any plans to use some sort of offset cross brace from mount to mount under the subframe? Seems like those studs may rip the frame when the engine rocks.
Re: Project: Slideways z26
Posted: Wed Feb 08, 2012 2:29 pm
nevermind that, I'd be more afraid of the tail shaft ripping the floor pan up as it rocks up front... There is no structure to what he bolted that to... Also you didn't center the engine on purpose correct?
Re: Project: Slideways z26
Posted: Wed Feb 08, 2012 5:52 pm
Yes actually, pretty much exactly that. Along with another one right behind the oil pan between the subframesMoney pit Beretta wrote:Any plans to use some sort of offset cross brace from mount to mount under the subframe? Seems like those studs may rip the frame when the engine rocks.