Project B - 1991 3400 OBII 5-Speed

[Luckymc420]

The bottom picture I hear is for the key so if you shut the car off in gear and dont put it into park it wont release the key.  That other picture I just dont know what the hell it is.  I dont think I added it..  I know I will not get anything done on it till maybe the 1st like in the PM Thats hang over day.  But I got to get ready for school to start back up again. GOD I want to quit it.

[Money pit Beretta]

Don't quit school, or you will end up like me in a low pay job. I don't make enough to move out and pay for the repair and build of my car. I've been out before and that's how I lost my 83Z28 and got the Beretta(my Dad had to buy it for me). The Z story is a long one so I won't go into it. Keep up the good work!

[Money pit Beretta]

So far no luck on the throttle cable. Those things are hard to find. What's going on, anything new? I check this post everytime I'm on. Do you just want a new throttle cable or can you use an old one?

[Luckymc420]

Well I have been trying to get this A/C delete pully figured out.  I keep getting the wrong part.  I (think) I have a 2002 Grand am engine. The bracket I keep getting won't fit.  I also just started school agaiin so last week was just trying to get in the role of things.  I have not really focused on the project for a few weeks now.  Hopefully I can get parts this week that will work.

[Money pit Beretta]

Well at least you got some time off, I hit my 67 Camaro project for 2 years without any time off and burned out(also found out the thing was too far gone). Glad to hear that you are still going.

[Luckymc420]

Well I got the AC pully figured out.  And I also updated my list page at Bnet.

Quick Link

[Money pit Beretta]

I see alot of people over there that I have seen here. Kinda wish we were all on one site, but that's just how it is, that's ok. I picked this site because I like how it's set up. Good to see that you have so much support. I haven't had time to look for the cable. I have a new coolant leak, also need to get a strut tower bar on after I get some small rust areas off. If you need me to look for anything else I'll be happy to help.

[Luckymc420]

I really have not done to much with it. I am not liking this cold *** weather plus I still feal like crap.  But tommrow I have a short day is class so I might come home and start learning how to weld with my welder.  And hopfully I will get the AC Spacer tommrow and then be able to call the engine DONE!  I just can not beleve that I have spen 5 grand on this thing and thats without the turbo setup. Thats another 2 grand.

[Money pit Beretta]

It's too cold here also(it will be 17 saturday). Just be happy that you have good weather strip, it's hard to find and cost alot. When the turbo set up is done I'd bet it will be more than 2G's.

[Luckymc420]

It just snowed all day today so i was out cleaning the drive way off.  WELL I did go back in the garage and strike up an arc.  I did about 20 passes. By that time the garage was fulled with fumes.  It didnt look to bad.  I am sure after I am done with this welding class i should be fine.

[Money pit Beretta]

It's been almost 2 years, I don't know if I can still use an arc(wire welding is easy). Look out when online parts shopping. I have been talking to this place online for door panels. First they ask me where they go, then they tell me that my VIN is for a Corsica. Sorry, just felt like getting that off my chest. How's everything with you?

[Luckymc420]

Well I need to find bolts long enough to bolt up this ac pully.  Then i Dont know i need to see what i have left to do.

[Luckymc420]

WELL...

I went got some fuel for my heater. 4.50/Gal. DAMN!!! got 40 bucks worth.  I went out and looked over what I needed to get the engine running.

Throttle cable - I need to call that site and see if that is the right part.
Clutch - I am looking up info on the getrag 282 and see if the cluth I put in the 2.2 tranny  
           will fit or if I will need to buy another one.
Weld a support bracket for top right mount, - Learning how to weld so who knows....
Weld mount on the lower right.
Weld mount on the back right side.
Replace Heater Core - Picking up part tommrow
Exhaust work
Engine Oil filter adapter
Bypass AC Pully Bolts - Will see if napa has them
Fuel lines - I think I can get them to work without messing with them
Check my VSS wiring.

If you know something I am looking for let me know!

After all that I looked around and saw the shop was a freakin mess. SO I am in the cleaning phase.  Ill be doing this tommrow also.

[Money pit Beretta]

Wish I could say that I had something for you. I've been ordering alot of parts for my car. The thing is only one will make my car run better, the others are weatherstrip. So far I have put almost 3G's in this car and it's still slow and needs paint. I hope to get the engine and trans rebuild started sometime in this year. Should I check the master list for parts you need? Or is there something new that is needed. Hey, do you still have the exhaust heat shields? Eddie needs some, I told him to contact you. He has a post in the Wanted area.

[Luckymc420]

The only thing I really need is information on the clutch problem. I really cant find what I am lookin for.  Yea I talk to eddie and linked him to my post and i have not heard back from him.?