what did you do to your ride today?

[SummitBalt08]

Yeah but I had to replace the lense too. It was cracked and had a chunk missing out of the glass part. That's why I had to remove the whole thing.

Doesn't matter. The unit is a one piece assembly, you don't take the lens/refractor out of its holder, you just unbolt the 2 bolts that hold the whole thing into the inner steel bumper. Once its out of the car, then you can disassemble it into its 2 main pieces, the adjuster/holder and the light assembly, which can also be further dismantled, as the glass is adhered to the refractor with black silicone. I should know, I have had to completely rebuild my current set. And you do not have to take the cover off. Its easiest from the bottom with the bottom black plastic cover removed, but often the screws rust in place, so next step is from above by removing the headlight/lights, and possibly the support panel.

Oh I see.. that's would have saved me a lot of time lol. Now I know for.next time and when I fix the black Z's foglights

[3X00-Modified]

Got my new Drag Radials... I have heard Hoosier is the best DR tire









I spent $325 on the setup plus $41 shipping... a guy on 60* had them for his GA, they've never been run at the strip yet but he had them mounted up once on his car for a photo.

Might just spray the spokes with plasti dip to make them black so they "match" the rear rims I have.

[DTMAce]

Installed my decklid finally. One less thing that I have to do now.

[scd88ga]

How hard do you think it would be to grab that stereo mount and harness?

I have an extra stereo mount kit that's brand new in the package, and I may have an extra harness too! I'll PM you with pics and info later today!

[Robert 89gt]

Jon always fines killer deals.I changed my fuel pump again in my olds.Now it makes it up hills.lol

[Trevor]

Filled up the antifreeze (Which seems to be running out every couple of weeks :/), and got wiper fluid because i was out. Bone Dry out.

Listened to the Catalytic converter rattle and smelled gas all day as usual... I wish there was a less expensive way to fix the issue with the cat, other than buying a new one... Wish I had a garage to work on the car as well lmao!

[sp33d1nc0rs1ca]

Noticed that my left front ventshade is about an 1/8th inch further back than the right. OCD pet peeves. Then contemplated on what kind of material to use on my headliner when i redo it. Getting excited to FINALLY finish my damn wheel project.

[DTMAce]

Found the exact headliner material at ... JoAnn's fabrics! 50 some inches wide, by whatever length you need. About 15 bucks a yard length.

Has the foam and the close color of grey material. All you need to do is drop the current headliner, sand or rub away the old foam and material, get a can of 3M spray adhesive, follow directions and reapply the new material. Then trim and re-install. Done.

[sp33d1nc0rs1ca]

haha Thanks Chris. I know how to do it. i just cant make up my mind whether or not to do plain black or do something funky like Realtree camo. lol. and thanks for the tip too. there is a surplus store about 30 mins from me that sells headliner material in all different styles.

[scd88ga]

Getting excited to FINALLY finish my damn wheel project.

I still have those Z24 center caps if you want!

[theSLEEPER]

Still have to do the taillights.... Going to try to get some VHT Niteshades and make it look flat...
I'll edit this with a better picture in a bit...

[berettaboi]

do you like the flat? looks awesome when you use night shades, and then clear coat it

[theSLEEPER]

I like the flat. I've used Niteshades a lot. I'd rather clearcoat it so it holds up, but I'd have to find some flat clearcoat...

[berettaboi]

yup they offer that as well.. even at walmart i think

[Robert 89gt]

Had to replace my cover for my light under the hood.
Went to the yard after work and found a really nice one=)