Car is now gone. PARTS REMAIN THOUGH! Updated 11-18

[DTMAce]

Parts Pending:

Parts Sold:

• MAP sensor
  Mirrors
  Turn signal stalk
  Mirror trim, drivers side
  Inner Dew Strips
  Dome Light
  Spare Tire Bolt
  Foam Brick, Jack and wrench
  Headlights
  Door Handles
  Sail Panels
  Pass side front pillar
  Key locks
  Wiper Control
  Lock switch
  Upper Filler
  Wiper sprayer hoses
  Rear bumper Chevrolet decal
  Grill

Parts Currently Left Available to buy that are known to be good. ALL PRICES ARE SHIPPED (in USA) PRICES. I will combine for multiple stuff to save you some on shipping.

• Front base bumper, great condition - $50 PLUS SHIPPING DUE TO SIZE!
  Rear View Mirror - $15
  Exterior Lock Applique Panels - $20
  Step panels (black and in good shape) - $30
  Carpet Stays (both are in decent shape, small chip on rear of passenger one) - $30
  Kick panels - $20
  Cargo net and brackets - $20
  Shifter handle, plastic retainer, boot (needs cleaned) - $15
  Rear Lower Filler Support Panel - $40

See later post for the last pics of beretta before going to the scrap yard.

Item in question will be looked over, removed if need be to inspect it thoroughly. Cleaned if needed and then presented for approval of buyer with pics/description of condition. Once approved, buyer will have 2 business days to pay for the item unless other arrangements are pre-agreed on.

I will make every effort to present the item as it is, and list it with any flaws, marks or other conditions that may limit its desirability, but I make no guarantees that the item will always be 100 percent what I think it may be. We all know each person has their own interpretation, but I usually try to hold to a high standard. So if for any reason anyone is not happy, or feel they did not get what they expected, I will work with you to make it right, if need be. Pics of items may be displayed publicly for opinions on condition, unless buyer requests otherwise in these cases.

Payments will be done with paypal. If you do not have paypal, no sweat, you can still send someone money with paypal using a debit or credit card to do your purchase.

Shipping:

I am including the shipping price with the purchase price for simplicity. All shipments will be UPS, unless otherwise needed due to size etc. Large or heavy items may cost more individually. Will be using good packing materials and in some cases making custom cardboard boxes. I will do my best to pack the items to protect them, but things happen. UPS has insurance automatically for up to 100 dollars, if your purchase happens to be more than that, I will insure it appropriately.

Pics!



































Good luck, and again, time is limited! Post or PM your inquires, I will answer as quick as I can! Thanks again!

[Robert 89gt]

What Do the shift cables look like??
If it's the isuzu trans there not the same.
Maybe take a pictures for me??And take some measurements?
Please and thank you

[Amateur]

I am interested in the shift cables (can never have to many of those amirite). The '94 have the same style ends as the '95 right? not to sure but if its all plastic on the ends with the o bushings then we're in business.

So I would take both the shifter and selector cables off your hands, just name your price. (assuming they are the ones). Thanks

[DTMAce]

Well, have to see. Have one ahead of the other here. lol

Will get into those soon. Have my son here this weekend. Pics are coming up next, just got done shooting a bunch.

[Amateur]

Well, have to see. Have one ahead of the other here. lol

Will get into those soon. Have my son here this weekend. Pics are coming up next, just got done shooting a bunch.

of course, Robert89gt has first dibs.

[DTMAce]

Above is a pic of the tranny side of the shift cables. The shifter does go through the gears ok, or seems too, so the cables appear to work. I have yet to pull the console apart.

Expanded list of what I plan to keep:
Top windshield gasket.
Rear seam top rubber pieces.
Side markers (for LED conversions)
Pass rear tail light, maybe the driver side too. Neither are in great shape anyway, but will work for my LED stuff.
Front base lamps. Again for LED mockup work. They look to be in decent shape, would sell if someone needs them.
All of the door window trim including dew strips. Mirrors I don't really want.
May be a few other things, as I come across them.

187k on the clock.
Gas hinge seems to be bad. (hanging down)
Arm rest cover is trash. Rest of interior is there, minus a good cleaning needed...

Anyway, ask and I will see, if its worthwhile you are welcome to it Pics if requested, no problem.

[michi]

wow i have never seen such bad rusted door jams... sorry for offtopic

[DTMAce]

No worries. Just got done using a pressure washer on it. Actually the headlights are in really nice shape, I was surprised. Front grill is nice, front bumper is really decent. Rear bumper isn't too bad. Red paint is still bright, surprisingly. Washed the engine bay too, but more to do.

I will be hitting it again with the washer, on the inside I think. Yikes. Driver's side door gasket (on the car body) has been missing for some time, and the top of the door is pulled out from the body. So water has been running in through the door for awhile. BUT despite that, the door panel looks good. Go figure.

More as I get through it. Headliner is nice, but needs cleaned, and has a bit of separation where the mirror light wire hung down on it. Much of the parts can be saved, just have to clean it up.

[KFLO 93 GT]

I'd like the shift plate and boot - providing the combo has the metal retaining ring on the bottom side still intact. Truth be told - that metal retaining ring is all I'm after... but it never hurts to have a spare 5 speed shift plate either. Never know when I'll be swapping one.

[DTMAce]

What Do the shift cables look like??
If it's the isuzu trans there not the same.
Maybe take a pictures for me??And take some measurements?
Please and thank you

There is a picture of the tranny end up there now. They appear to be ok, and seem to operate correctly.

Measurements of what exactly?

And as stated it is the Isuzu tranny.

I am interested in the shift cables (can never have to many of those amirite). The '94 have the same style ends as the '95 right? not to sure but if its all plastic on the ends with the o bushings then we're in business.

So I would take both the shifter and selector cables off your hands, just name your price. (assuming they are the ones). Thanks

If you can see the above pic of the tranny where the line is connected, it looks to be what you are after. If Robert passes, you can have them and the shifter. What I would like to know is do you need to console/boot and plate? If not, then I can save them for....

I'd like the shift plate and boot - providing the combo has the metal retaining ring on the bottom side still intact. Truth be told - that metal retaining ring is all I'm after... but it never hurts to have a spare 5 speed shift plate either. Never know when I'll be swapping one.

Let me know guys. I won't be able to try to pull the cables till sometime later this following week. And I have never pulled them before so may need some suggestions. lol

Thanks.

[Robert 89gt]

Yeah i'll take the cables if there not seized??
Please and thank you

[DTMAce]

More updates.

I have connected a battery and tested the electrical sides of things. Engine definitely won't turn over, seems to be stuck. Yes I depressed the clutch, just get a hard click and it sounds like the starter grunts for a split second but no go. Missing 3 spark plugs too. lol Fuel pump runs though.
Blower motor works. Interior lights work, so if the module is good, I'm yanking that for my Z, as my interior lights will not come on unless I flip the dome switch.

Looks like the radio and speakers are good.
Lights seem to work, wipers work, etc.
Brights switch works.
I'm pulling the air vents and radio console cover, as most of my vents are all screwed up anyway.

Keep asking, I will keep going through it.

Looks a bit better on the outside. Also looks like the lower base trims are in nice shape, if anyone wants them. The one on the front bumper looks excellent, I think I only found one scuff on it that stood out. Headlights are definitely in decent shape, I can easily pull them.


More on the list of good:

Rear filler panel both upper and lower are in good shape, no cracks that I can see. Lower fiberglass filler is also intact. Both bumper covers are in decent/reusable shape. Decklid is decent. Lots of good parts really.

You want to know about a part? ASK!!!

[DTMAce]

Yeah i'll take the cables if there not seized??
Please and thank you

As I said, the shifter seems to move through the gears fine, so it looks like the cables are good. How do I remove these properly? Which end first, and what needs done at the firewall? Do you need the shifter itself? Or do you want just the cables?

[KFLO 93 GT]

I'm talking the plastic plate that snaps into the console. Then the shift boot that is hopefully bolted to that plate via the metal retaining ring (the retaining ring deal is what I really want and need, but there is no need to separate because I'll buy all 3 pieces). Don't need the lighter well or trunk release button, but you can leave them in if you don't want to pull them, I don't care. I Don't need the shift arm or knob either.

Hope that helps.

[DTMAce]

Hmmmm Then I guess having the boot be loose already is not a good sign.

I will have to pull the console, see what it has. It will be Monday or Tuesday before I get that all apart in there, weather depending. There is no trunk release on this one. HA.

Thanks for the clarification.